background image

© 2007 HeathCo LLC 

598-1120-04

Requirements

•  The light control requires 120-volts AC.
•  If you want to use Manual Mode, the control must be 

wired through a switch.

• 

Some  codes  require  installation  by  a  
qualified electrician.

•  This product is intended for use with the enclosed 

gasket and with a junction box marked for use in wet 
locations.

• 

Note: This product is not recommended for use where 
the outside temperature is below -10° F.

Model SL-5710

Light Control

Sensor

Cover Plate

Lamp Holders

Features

•  Turns on lighting when motion is detected.
•  Automatically turns lighting off. 
•  Photocell keeps the lighting off during daylight hours.
•  LED indicates motion was sensed (day or night).
•  Additional energy savings with compact fluorescent 

bulbs.

Motion Sensor
Light Control

Plastic Hanger

Rubber Plug

Gasket

6 Screws

(3 sizes included)

Mounting Strap

Mounting Bolt

2 Compact

Fluorescent Bulbs

2 Wire

Connectors

This package includes:

OPERATION

* resets to Auto Mode at dawn.

Note:  When first turned on wait about 1 

1

/

2

 minutes for 

the circuitry to calibrate.

MANUAL MODE

ON-TIME

10 5 1 TEST

10 5 1 

TEST

ON-TIME

TEST

... back on.

AUTO

1 Second 

OFF 

then...

Put the ON-TIME switch in the 1, 5, or 
10 minute position. 

Note: Although the 

1 minute mode can be used, the 5 or 
10 minute mode is recommended for 
best operation and performance when 
using compact fluorescent bulbs.

Put the ON-TIME switch on the bottom 
of the sensor in the TEST position.

Manual  mode  only  works  at  night 
because daylight returns the sensor 
to AUTO.

Flip the light switch off for one second 
then back on to toggle between AUTO 
and MANUAL MODE.

Manual  mode  works  only  with  the 
ON-TIME  switch  in  the  1,  5,  or  10 
position.

Move ON-TIME Switch to 

1, 5, or 10 minutes

Mode Switching Summary

Flip light switch off 

for one second then 

back on*

MANUAL MODE

AUTO

TEST

*  If you get confused while switching modes, turn the 

power off for one minute, then back on. After the cali-
bration time the control will be in the AUTO mode.

Mode:

On-Time

Works:

Day Night

Test

5 Seconds

x

x

Auto

1, 5, or 10 Min

x

Manual

Until Dawn*

x

Summary of Contents for SL-5710













Reviews:

Related manuals for SL-5710