Heat & Glo REVO-H31 Installation Manual Download

Page: 1 / 69

Heat & Glo • REVO-V12, REVO-S21, REVO-H31 Installation Manual • 2273-980 Rev. J • 5/15

Models:

Installation Manual

Installation and Appliance Setup

Pour demander un exemplaire en français de ce Manuel

du propriétaire, visitez www.heatnglo.com/translations.

INSTALLER: Leave this manual with party responsible for use and operation.

OwNER: Retain this manual for future reference.

REVO-V12

REVO-S21

REVO-H31

NOTICE: DO NOT

discard this manual!

In the Commonwealth of Massachusetts installation must be

performed by a licensed plumber or gas fitter.

See Table of Contents for location of additional Commonwealth

of Massachusetts requirements.

This appliance may be installed as an OEM

installation in manufactured home (USA

only) or mobile home and must be installed

in accordance with the manufacturer’s

instructions and the

Manufactured Home

Construction and Safety Standard,

Title 24

CFR, Part 3280

in the United States, or the

Standard for Installation in Mobile Homes,

CAN/CSA Z240 MH Series,

in Canada.

This appliance is only for use with the type(s)

of gas indicated on the rating plate. This

appliance is not convertible for use with other

gases, unless a certified kit is used.

•

DO NOT

store or use gasoline or other flam

mable vapors and liquids in the vicinity of this

or any other appliance.

• What to do if you smell gas

DO NOT

try to light any appliance.

DO NOT

touch any electrical switch.

NOT

use any phone in your building.

- Leave the building immediately.
- Immediately call your gas supplier from

a neighbor’s phone. Follow the gas sup-

plier’s instructions.

- If you cannot reach your gas supplier, call

the fire department.

• Installation and service must be performed

by a qualified installer, service agency, or the

gas supplier.

wARNING:

FIRE OR EXPLOSION HAZARD

Failure to follow safety warnings exactly

could result in serious injury, death, or

property damage.

DANGER

HOT GLASS

WILL

CAUSE BURNS.

DO NOT TOUCH

GLASS

UNTIL COOLED.

NEVER

ALLOW CHILDREN

TO TOUCH GLASS.

A barrier designed to reduce the risk of

burns from the hot viewing glass is provided

with this appliance and shall be installed for

the protection of children and other at-risk

individuals.

Summary of Contents for REVO-H31






































































Search results

Summary of Contents for REVO-H31

Reviews:

Related manuals for REVO-H31

Brands by name

Popular brands

Heat & Glo REVO-H31, Installation Manual

Search results

Summary of Contents for REVO-H31

Reviews:

Related manuals for REVO-H31

Brands by name

Popular brands