Hayward TriStar VS SP3215VS Owner'S Manual Download

Page: 1 / 16

30-LITINSB004 Rev-B

SAVE THIS INSTRUCTION MANUAL

Hayward Pool Products (Australia) Pty Ltd.

Melbourne-Sydney-Brisbane-Perth

Email: [email protected] Website: www.hayward-pool.com.au

P.O Box 4384, Dandenong South, VIC. 3164

ABN 66 083 413 414

Sales Ph 1300POOLS1 Fx 1300POOLS2

TriStar VS

NOTE: To prevent potential injury and to avoid unnecessary service calls,

read this manual carefully and completely.

The Hayward TriStar Variable Speed Pump is specifically engineered for the demanding

requirements of today’s in-ground swimming pool/spa that is equiped with large capacity

filters, heaters, and pool cleaning equipment. The variable speed, totaly enclosed

permanment magnet motor, combined with its advanced hydraulic design, optimizes the

three essiential pump elements to deliver superior flow, energy efficiency, and quietness.

3200 SERIES SELF-PRIMING

Model - SP3215VS

TriStar Variable Speed Pump

Owner’s Manual

Summary of Contents for TriStar VS SP3215VS

















Search results

Summary of Contents for TriStar VS SP3215VS

Reviews:

Related manuals for TriStar VS SP3215VS

Brands by name

Popular brands

Hayward TriStar VS SP3215VS, Owner'S Manual

Search results

Summary of Contents for TriStar VS SP3215VS

Reviews:

Related manuals for TriStar VS SP3215VS

Brands by name

Popular brands