background image

3-90-233R24_11/13

Contact your local dealer with questions on installation, 

operation or service.

SAFETY NOTICE

PlEASE rEAd ThIS ENTIrE mANuAl bEFOrE YOu INSTAll ANd uSE YOur NEw bOIlEr. FAIlurE TO FOllOw 

INSTruCTIONS mAY rESulT IN PrOPErTY dAmAgE, bOdIlY INjurY, Or EvEN dEATh.
FOr rESIdENTIAl uSE IN ThE u.S. ANd CANAdA. 
IF ThIS PEllET bOIlEr IS NOT PrOPErlY INSTAllEd, A hOuSE FIrE mAY rESulT. FOr YOur SAFETY, FOllOw 

INSTAllATION dIrECTIONS. 
CONTACT lOCAl buIldINg Or FIrE OFFICIAlS AbOuT rESTrICTIONS ANd INSTAllATION INSPECTION 
rEQuIrEmENTS IN YOur ArEA.
CONTACT YOur lOCAl AuThOrITY (SuCh AS muNICIPAl buIldINg dEPArTmENT, FIrE dEPArTmENT, FIrE 

PrEvENTION burEAu, ETC.) TO dETErmINE ThE NEEd FOr A PErmIT.
CETTE guIdE d’uTIlISATION EST dISPONIblE EN FrANCAIS. ChEZ vOTrE CONCESSIONNAIrE dE hArmAN

SAvE ThESE INSTruCTIONS

Installation & Operating manual

model(s):

HydroFlex 60 Pellet Boiler

NOTICE: SAVE THESE INSTRUCTIONS

hot glass will cause burns.

•  Do not touch glass until it is cooled
•  NEVER allow children to touch glass
•  Keep children away
•  CAREFULLY SUPERVISE children in same room as 

stove.

•  Alert children and adults to hazards of high temperatures.

  high temperatures may ignite clothing or other 

flammable materials.

•  Keep clothing, furniture, draperies and other flammable 

materials away.

hOT SurFACES!

Glass and other surfaces are hot during 

operation and cool down.

WARNING

!

To  obtain  a  French  translation  of  this  manual,  please 

contact your dealer or visit www.harmanstoves.com

Pour obtenir une traduction française de ce manuel, s’il 

vous  plaît  contacter  votre  revendeur  ou  visitez  www.

harmanstoves.com

NOTE

Summary of Contents for HydroFlex 60 Pellet Boiler





















































Reviews: