background image

Installation and service must be provided by a qualified installer, service agency or the gas supplier. 

PO 

INSTALLATION GUIDE FOR 

HARGROVE VENTED GAS LOGS 

Dexen Electronic Ignition Pilot Valve (DEI-PO)   

 
 
 

 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

 

 

 
 
 
 
 

 

CAUTIONS 

1. 

This valve should be installed only by 
a qualified service technician trained 
in gas safety equipment.

 

2. 

Turn off the gas supply before 
installing the valve.

 

3. 

All piping must meet applicable local 
codes and ordinances and the 
National Fuel Gas Code (ANSI 
Z223.1/NFPA NO.54)

 

4. 

All wiring must meet the applicable 
electrical codes and ordinances.

 

5. 

Assure that the complete system is 
operating according to the 
manufacturer’s instructions after 
installing the Parts Only Kit.

 

6. 

Prior to installation, verify 
conformance with the log unit’s 
installation instructions.

 

7. 

Assure that all the piping is free of 
any foreign matter.

 

 

FOR YOUR SAFTEY 

DO  NOT  STORE  OR  USE  GASOLINE  OR 
OTHER 

FLAMMABLE 

LIQUIDS 

OR 

FLAMMABLE VAPORS IN THE VICINITY OF 
THIS OR ANY OTHER APPLIANCE

FOR YOUR SAFETY 

WHAT TO DO IF YOU SMELL GAS 

1.  Open windows. 
2.  Extinguish all open flames. 
3.  Do not try to light any appliance. 
4.  Do not touch any electrical switch; do 

not use the phone in your building. 

5.  Immediately call your gas supplier from 

a neighbor’s phone.  Follow the gas 
supplier’s instructions. 

6.  If you cannot reach your gas supplier, 

call the fire department

WARNING 

To avoid a potential fire hazard, do not 
disassemble or attempt to repair the safety 
gas valve.  Disassembly, reassembly or 
internal adjustment could cause the valve 
to malfunction, resulting in property 
damage, personal injury, or death.  If the 
control valve does not operate properly 
following the installation or service, 
replace the unit. 

INSTALLING A HARGROVE SAFETY GAS VALVE 
IN A LOCATION OTHER THAN SPECIFIED IN THIS 
MANUAL WILL VOID THE WARRANTY EXCEPT 
WHEN THE SAFETY GAS VALVE IS INSTALLED 
OUTSIDE THE FIREBOX IN A SAFE AND PROPER 
INSTALLATION AND ACCESS IS PROVIDED FOR 
MAINTENANCE AND REPAIR OF THE SYSTEM.  A 
QUALIFIED INSTALLER MUST MAKE 
INSTALLATION AND ADJUSTMENTS.
 

 

FOR YOUR SAFETY 

WARNING:  

If you do not follow these instructions exactly, a fire or explosion may 

occur resulting in property damage, personal injury, or loss of life. 

REV 122216

 

Summary of Contents for DEI-PO







Reviews: