▍Suffix code
28, Gilpa-ro 71beon-gil,
Michuhol-gu, Incheon, Korea
TEL : +82-32-876-4697
http://www.hanyoungnux.com
HANYOUNGNUX CO.,LTD
Slim-type single-phase Solid State Relay
HSR-SL
Thank you for purchasing Hanyoung Nux products. Please read the instruction
manual carefully before using this product, and use the product correctly.
Also, please keep this instruction manual where you can view it any time.
MC1301KE230302
INSTRUCTION MANUAL
▍Safety information
DANGER
Indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury
WARNING
Indicates a potentially hazardous situation which, if not avoided, could result in death or serious injury
CAUTION
Indicates a potentially hazardous situation which, if not avoided, may result in minor injury or property damage
Before using the product, please read the safety information thoroughly and use it properly.
Alerts declared in the manual are classified to
Danger
,
Warning
and
Caution
by their criticality.
• The input/output terminals are subject to electric shock
risk. Never let the input/output terminals come in contact
with your body or conductive substances.
DANGER
• Please make sure that the product specifications are the
same as you ordered.
• Please use the product in places where corrosive gases
(especially harmful gases, ammonia, etc.) and flammable
gases are not generated.
• Please use the product in places without liquids, oils,
chemicals, steam, dust, salt, iron, etc. (pollution degree 1 or 2).
• Please avoid places where large inductive interference,
static electricity,magnetic noise are generated.
• Please avoid places with heat accumulation caused by
direct sunlight, radiant heat, etc.
• When water enters, short circuit or fire may occur, so
please inspect the product carefully.
• Do not connect anything to the unused terminals.
• For DC types, please wire correctly, after checking the polarity
of the terminals.
• When disposing of the product, treat it as industrial waste.
• Pay attention to the edge of the heat sink, which may be sharp.
• The temperature of the main body and the heat sink may
become extremely high when electric power is applied,
which may cause burns.
• In case of product malfunction, remove only the main body.
• Because the SSR heats up when power is on, the lower the
heat sink and ambient temperatures, the longer the life.
• Note 1) If using a separate heat sink, use one that meets
the thermal resistance table.
• Please read the safety information carefully before the use,
and use the product correctly.
• If there is a possibility that a malfunction or abnormality of
this product may lead to a serious accident, install an
appropriate protection circuit on the outside and plan to
prevent accidents.
• Please supply the rated power voltage, in order to prevent
product breakdowns or malfunctions.
• To prevent electric shocks and malfunctions, do not supply
power until the wiring is completed.
• Please disassemble the product after turning OFF the power.
• Any use of the product other than those specified by the
manufacturer may result in personal injury or property
damage.
• Please use this product after installing it to a panel,
because there is a risk of electric shock.
• 4 - 32 V d.c model signal inputs must be supplied with
an isolated and limited voltage/current or Class2,
SELV power supply.
• Short circuit rated current is 3kA.
WARNING
CAUTION
■ CE, UL certified products
Model
Code
Content
HSR-SL
□ □ □ □ □ □ Slim-type single-phase Solid State Relay
Control input
voltage
D
4 - 32 V d.c.
A
90 - 240 V a.c.
Rated load current
15
15 A
25
25 A
40
40 A
Operating load voltage
L
24 - 240 V a.c. (Low voltage)
H
24 - 480 V a.c. (High voltage)
Method of operation
Z
Zero-cross switching (standard product)
R
Random switching
Heat sink & Option
S
Integrated heat sink (standard product)
T
Heat sink + Bimetal mounted
N
No heat sink
※CAUTION 1) When using a separate heat sink,
you must use a heat sink that meets the thermal resistance table.
point of contact
1C 1 Point of contact (Unmarked)
2C 2 Point of contact (Unmarked)
※CAUTION 2)
Only for 15 A
■ S-MARK certified products
▍Equivalent Circuit
C1
C2
L1
Trigger Circuit
Input Circuit
L2
(~)
+
-
(~)
▍Connection diagram
※ This model does not have a fuse internally.
So we suggest using fast-acting fuse separately on the outside as following pictures.
■ Load and
input voltage
wiring diagram
■ BI Option spec diagram
(60℃, 80℃ bimetal mounted)
Input
the
PLC
etc.
+
-
Load
voltage
FUSE
80
℃
Bimetallic
Input
voltage
4
-
32
V
d.c.
LOAD
Input
voltage
90
-
264
V
a.c.
88
210
210
18.5
60
℃
Bimetallic
Bimetallic
※ Bimetal specification
-Operating temperature: 60℃ / 80℃
-Temperature tolerance: Display temperature ±5℃
-Rating (resistive load): 3 A or less / 48 V d.c.
1 A or less / 277 V a.c.
▍Specifications
▍Dimensions
[Unit : mm]
● 15A, 25A
● 2C
(2 Point of contact)
● N
(Heating plate removal )
■ CE, UL certified products
● 40A
● 40A
● 15A
● 25A
■ S-MARK certified products
Model
Code
Content
HSR-SL
□ □ □ □ □ -S Slim-type single-phase Solid State Relay
Control input
voltage
D
4 - 32 V d.c.
Rated load current
15
15 A
25
25 A
40
40 A
Operating load voltage
L
24 - 240 V a.c. (Low voltage)
H
24 - 480 V a.c. (High voltage)
Method of operation
Z
Zero-cross switching (standard product)
Heat sink & Option
S
Integrated heat sink (standard product)
T
Heat sink + Bimetal mounted
N
No heat sink
※CAUTION 1) When using a separate heat sink,
you must use a heat sink that meets the thermal resistance table.
Model
Low HSR-SLD15LR□□ HSR-SLD25LR□□ HSR-SLD40LR□□ HSR-SLA15LR□□ HSR-SLA25LR□□ HSR-SLA40LR□□
HSR-SLD15LZ□□ HSR-SLD25LZ□□ HSR-SLD40LZ□□ HSR-SLA15LZ□□ HSR-SLA25LZ□□ HSR-SLA40LZ□□
High HSR-SLD15HR□□ HSR-SLD25HR□□ HSR-SLD40HR□□ HSR-SLA15HR□□ HSR-SLA25HR□□ HSR-SLA40HR□□
HSR-SLD15HZ□□ HSR-SLD25HZ□□ HSR-SLD40HZ□□ HSR-SLA15HZ□□ HSR-SLA25HZ□□ HSR-SLA40HZ□□
SLow HSR-SLD15LZ□-S HSR-SLD25LZ□-S HSR-SLD40LZ□-S
SHigh HSR-SLD15HZ□-S HSR-SLD25HZ□-S HSR-SLD40HZ□-S
LO
AD
Rated Load Voltage
Low
24 - 240 V a.c. 50/60 Hz
High
24 - 480 V a.c. 50/60 Hz
Peak Voltage
(Non-repetition)
Low
1,200 V
High
Rated load current
15 A
25 A
40 A
15 A
25 A
40 A
Surge current 60 Hz
(8.3 ms No repetition)
Low
170 A
260 A
420 A
170 A
260 A
420 A
High
170 A
250 A
370 A
170 A
250 A
370 A
Surge current 50 Hz
(10 ms No repetition)
Low
160 A
250 A
400 A
160 A
250 A
400 A
High
160 A
230 A
350 A
160 A
230 A
350 A
Leakage current
Less than 20 mA
Output ON voltage dropping
Less than 1.6 V (R.M.S)
INPUT
Rated Voltage
5 - 24 V d.c.
100 - 240 V a.c. 50/60 Hz
Operating Voltage Range
(ON Voltage)
4 - 32 V d.c.
90 - 264 V a.c. 50/60 Hz
return voltage (OFF Voltage)
Less than 3 V
Less than 50 V
Impedance
Less than 4 kΩ
Less than 40 kΩ
Current consumption
Constant current method : Less than 14 mA
Less than 14 mA
Response Time
1/2 Cycle + 1 ms max. (“R” type below 1 ms)
Insulating Resistance
500 V d.c., 100 MΩ (Between the input / output and case)
Dielectric strength
2,500 V a.c. (For 1min at 60 ㎐)
Rated impulse withstand voltage (Uimp)
2,500 V
Vibration resistance
10 - 55 Hz, Constant current method : 1.5 mm,X·Y·Z each axis direction for 2 hour
Shock resistance
1,000 ㎨, X·Y·Z each axis 3 times
Storage Temperature
-30 ~ 90 ℃
Ambient Temperature
-30 ~ 80 ℃ (no condensation)
Ambient Humidity
45 ~ 85 % RH
Pollution level grade
2 Level
bolt tightening torque
Input terminal: 0.05 Nm / Output terminal: 0.25 Nm
Usage
Resistive load
certification
(EN 60947-4-3)
Weight Integrated heat sink (with box)
Approx. 226 g
Approx. 266 g
Approx. 226 g
Approx. 266 g
Weight Heating plate removal (with box)
Approx. 94 g
▍Installation intervals
• Please make intervals
more than following picture.
• Please install wiring duct
less than half the height of
the heat sink to prevent
obstruction the flow of air.
• The optimal performance of our
HSR is in the ambient
temperature by 25 ℃ so please
use it lower than 25 ℃
▍Caution
• Since the width of the load output terminal is 10.6mm and the input terminal is 6.8mm,
use a smaller terminal than the standard and tighten it with the rated torque.
• When the product is defective, separate main body and exchange it.
• Use it under temperature 25 ℃ when a real load current is 35 ~ 40 A.
• When 40 A maximum load is used, use 10 SQ wiring. Use clamping unit or lug when tightening it.
▍How to install
• Please install HSR in the vertical direction.
• Otherwise, production performance
may be reduced to less than 50 %.
• Since the weight of the product is heavy,
install it stably when installing DIN rail
Vertical direction
Horizontality
direction
Horizontality direction
▍Load/Surge current Characteristics
■ Surge current Characteristics
Air
flow
Wiring
duct
Wiring
duct
Wiring
duct
Inlet
Over
60
㎜
Over
100
㎜
Over
30
㎜
Ove
r
10
㎜
Ove
r
10
㎜
FAN
Wiring
duct
■ Load current Characteristics
0
50
100
150
200
250
300
350
400
10
100
1
1000
40
A
15
A
25
A
Surge
Current
(A)
N
umber
of
Cycle
(60
Hz)
Ambient
Temperature
(℃)
Load
current
(A)
50
40
30
20
18
10
-30 -20 0
20 40 60 80 100
40
Ambient
Temperature
(℃)
Load
current
(A)
Ambient
Temperature
(℃)
Load
current
(A)
25
2
4
6
8
-30 -20 0
20 40 60 80 100
·
HSR-SL□15A
·
HSR-SL□25A
·
HSR-SL□40A
50
40
30
20
10
15
-30 -20 0
20 40 60 80 100
·
HSR-SL□40A
·
HSR-SL□25A
·
HSR-SL□15A
● Integrated heat sink
※CAUTION 2)
2 contact : Only available for 15 A items
(HSR-SL□15LZS2C, HSR-SL□15HZS2C )
17.4
4.5
5.5
90.0
99.0
4.5
44.4
98.5
29.0
80.42
17.4
4.5
5.5
90.0
99.0
4.5
22.4
17.4
4.5
5.5
90.0
99.0
4.5
45.4
72.
0
2-4.0
2-M3(TAP)
22.0
80.
0
±0.05
17.4
4.5
5.5
90.0
99.0
4.5
44.4
98.5
29.0
80.42
17.4
4.5
5.5
90.0
99.0
4.5
22.4
17.4
4.5
5.5
90.0
99.0
4.5
45.4
72.
0
2-4.0
2-M3(TAP)
22.0
80.
0
±0.05
17.4
4.5
5.5
90.0
99.0
4.5
44.4
98.5
29.0
80.42
17.4
4.5
5.5
90.0
99.0
4.5
22.4
17.4
4.5
5.5
90.0
99.0
4.5
45.4
72.
0
2-4.0
2-M3(TAP)
22.0
80.
0
±0.05
17.4
4.5
5.5
90.0
99.0
4.5
44.4
98.5
29.0
80.42
17.4
4.5
5.5
90.0
99.0
4.5
22.4
17.4
4.5
5.5
90.0
99.0
4.5
45.4
72.
0
2-4.0
2-M3(TAP)
22.0
80.
0
±0.05
17.4
4.5
5.5
90.0
99.0
4.5
44.4
98.5
29.0
80.42
17.4
4.5
5.5
90.0
99.0
4.5
22.4
17.4
4.5
5.5
90.0
99.0
4.5
45.4
72.
0
2-4.0
2-M3(TAP)
22.0
80.
0
±0.05
17.4
4.5
5.5
90.0
99.0
4.5
44.4
98.5
29.0
80.42
17.4
4.5
5.5
90.0
99.0
4.5
22.4
17.4
4.5
5.5
90.0
99.0
4.5
45.4
72.
0
2-4.0
2-M3(TAP)
22.0
80.
0
±0.05
17.4
4.5
5.5
90.0
99.0
4.5
44.4
98.5
29.0
80.42
17.4
4.5
5.5
90.0
99.0
4.5
22.4
17.4
4.5
5.5
90.0
99.0
4.5
45.4
72.0
2-4.0
2-M3(TAP)
22.0
80.0
±0.05
22.0
19.2
22.0
20.0
1.0
17.4
4.5
5.5
90.0
99.0
4.5
44.4
98.5
29.0
80.42
17.4
4.5
5.5
90.0
99.0
4.5
22.4
17.4
4.5
5.5
90.0
99.0
4.5
45.4
72.0
2-4.0
2-M3(TAP)
22.0
80.0
±0.05
22.0
19.2
22.0
20.0
1.0
.9%FQUI
※ CAUTION 1
load
capacity
Heatsink
thermal
resistance
15A
0.92 ℃/W
25A
0.71 ℃/W
40A
0.25 ℃/W
• Input terminal wiring
• Output terminal wiring
1 X 0.5 mm² (1 X AWG20) or larger
1 X 1.5mm² (1 X AWG16) or larger
1 X 1.5 mm² (1 X AWG16) or less than 2 X 1.5 mm² (2 X AWG16) 1 X 16 mm² (1 X AWG6) or less than 2 X 6 mm² (2 X AWG10)
※ Connect the wiring suitable for the
load current capacity to the output terminal.
25 ℃ 15A 25A 40A
80 ℃
6A
8A 15A
17.4
4.5
70.0
109.0 100.0 90.0
4.5 5.5
