![background image](http://html1.mh-extra.com/html/hampton-bay/hd28784/hd28784_use-and-care-manual_3484344001.webp)
Item #1001 492 696
Model #HD28784
Use and Care Guide
LOW VOLTAGE WALK LIGHT
PACKAGE CONTENTS
Assembly and Installation
1
Attaching and installing the light
2
Connecting the wires
WARNING:
Never push the fixture into the ground by the lamp body (A) or use a
hammer to insert the spike (G) into the ground.
WARNING: The wire connector (F) contacts have sharp edges for piercing the
main low voltage cable. To avoid injury, do not touch the metal contacts.
CAUTION: The wire from the low voltage power unit shall be 12-16 AWG type
underground low Energy Circuit Cable or SPT2W.
CAUTION: Safe for outdoor operation
WARNING: To reduce the risk of FIRE OR INJURY TO PERSONS:
WARNING: Turn off/unplug and allow to cool before replacing lamp.
WARNING: Lamp gets HOT quickly! Contact only switch/plug when turning on.
Do not touch hot lens, guard or enclosure.
WARNING: Keep the lamp away from materials that may burn.
WARNING: Do not touch the lamp at any time. Use a soft cloth. Oil from skin may
damage the lamp.
IMPORTANT:
• Protect the wiring by routing it in close proximity to the light fitting, or next to a
building structure such as a house or deck.
• The landscape wire and connector can also be hidden under stone or buried
under grass at a maximum depth of 6” (15.24 cm).
• Do not submerge fixture in water.
q
Carefully remove the fixture from its protective packaging.
q
Pass the wire through the spike (G).
q
Fix both post sections (E) together by turning clockwise.
q
Attach the spike (G) by pushing it into the lower post section.
q
Insert the bulb (B) into the bulb socket.
q
Attach the body by pushing the lens (C) onto the post.
q
Put the metal disks (D) on the lens by guiding them between the ribs on
the lens and turn clockwise to secure them.
q
Attach the cover (A) to the lens by turning clockwise.
WARNING: Risk of Electric Shock. Install all luminaires 10 ft. (3.05 m) or more
from a pool, spa or fountain.
WARNING: Install in accordance with all local codes and ordinances.
q
Place the wire connector (F) on opposite sides of the low voltage
cable (not included) where the fixture will be located.
q
Align and fit the main low voltage cable vertically to the slot of the
wire connector (F) as shown.
q
Press the wire connector (F) together until fully seated and locked
around the cable. Pre-set prongs will pierce the cable insulation
and establish contact. Turn on the power unit. If the light fixture
does not turn on, repeat the previous steps.
q
Once the clip-on connector (F) is in place, it is recommended to
wrap it with electrical tape for additional protection.
q
CAUTION BE CAREFUL! THE WIRE STABS ARE VERY SHARP!
q
After all fixtures are installed, turn on the transformer.
F
Only for use with low voltage power units with a maximum output rating of 15V,
300W per secondary.
FOR LANDSCAPE LIGHTING SYSTEMS ONLY. OUTDOOR USE ONLY. THE DEVICE IS
ACCEPTED AS A COMPONENT OF A LANDSCAPE LIGHTING SYSTEM WHERE THE
SUITABILITY OF THE COMBINATION SHALL BE DETERMINED BY CSA OR LOCAL
INSPECTION AUTHORITIES HAVING JURISDICTION.
UL LISTED UNDER MODEL # GL22784
Please read and save these instructions
INSTRUCTIONS PERTAINING TO A RISK OF FIRE, OR INJURY TO PERSONS
IMPORTANT SAFETY INSTRUCTIONS
Lighted lamp is HOT!
Part
Description
Quantity
A
Top cover
1
B
7W Incandescent T5 Wedge Base Bulb
1
C
Lens
1
D
Tier
2
E
Post
2
F
Connector
1
G
Spike
1
A
B
C
D
F
E
G
A
B
C
D
E
G