background image

HWM70-12688NZP

HWM60-12699NZP

HWM70-12688NZP

HWM60-12699NZP

1/12 2/18 3/24 4/29

5/33 6/37 7/41 8/46

L

 500mm W 520mm H 902mm

No or slow drain

the digitron 

displays“E1”,buzzing.

No or slow water filling

the digitron 

displays“E4”,buzzing.

The digitron displays“FA”,buzzing.

The machine does

 not act.

Not wash

Not spin

Water level sensor is abnormal?

Please contact with after-sales service 

department.

The water tap is not open.

The water inlet valve is blocked.

The water pressure is too low

 and the current is too small.

Are the laundries put slantingly?

Is the machine slanting?

Open the tap.Open and close the top lid once,

then press the START/PAUSE button. 

 Clean the water inlet walve,Open and close the

 top once.then press the START/PAUSE button. 

Wait for the normal water pressure before use.

Re-order the laundries.Close the top lid and    

press the 

START/PAUSE

  button.

Safety switch actuates,not spin,

(after self-correction twice),the digitron

 displays“E3”,buzzing.

Is the drain hose put down?

Is the drain hose blocked by

foreign material?

Put down the drain hose.Open and close the top  

lid once

then press the START/PAUSE  button

Clean the foreign material.Open and close the 

top lid once,then press the START/PAUSE  button

Level the machine in right position

Note: when the digital tube displays the abnormal symbol during working,it  buzzs once in 

         succession every two minutes,then the power will be cut automatically after ten minutes.

When the power plug is inserted, computer

board indicator is switched on, and the 

machine starts working.

It is the special resume function. In the case of power

failure or the power plug is loose during washing, the

machine can save the running program, and resume

the program after the power supply is recovered.

 

You

do not need to set the program again.

Is there power failure?

Is the power plug inserted tightly?

Is the water level reached preset

position?

Is the top lid closed?

Use it when there’s power supply.

Insert the power plug tightly.

Fill water to the preset position

Close the top lid

Is the power plug inserted tightly?

Is the top lid closed reliably?

Are the laundries set flat?

Insert the power plug tightly.

Close the top lid.

Set the laundries flat.

There’s abnormal sound

inside the machine

Is the machine slanting?

Are the laundries put slantingly in

spinning?

Adjust the machine to be even.

Reorder the laundries and close the

top lid.

The water tap leaks

Fasten the jointer properly.

 Is the jointer of water inlet hose

loose or twisted awry?

Summary of Contents for HWM70-12688NZP









Reviews: