Auto
Strong
E xtra Rinse
D elay
Star t /
R
S
S-D Inverter
Close the door; if the problem
remains, please ask for repair
Please ask for repair
Please ask for repair
Please ask for repair
Take out and fluff out the
clothes; if the problem
remains, please ask for repair
The washer automatically
removes this problem; if the
problem remains, please
ask for repair
Shut down the washer and
remove the problem; if the
problem remains, please ask for
repair
Shut down the washer and
remove the problem.
①
Check
whether the water tap is turned on,
whether the water pressure is too
low, whether water supply cut-off
occurs;
②
Check whether the
water inlet valve is clogged
(please clean it); if the problem
remains, please ask for repair
Clean the draining pump filter
and check whether the drain
pipe is clogged; if the problem
remains, please ask for repair
The washer is in automatic
weighing state
The remaining washing time is
one hour and sixteen minutes
The spinning speed is set
at 800 rpm
The whole program ends
Abnormal door locking or
unclosed door
Drainage fault
Temperature sensor fault
Heating fault
Abnormal water inflow
The motor speed is higher
or lower than the pre-set
speed
The motor stops running
The water level exceeds
alarm level
Water level sensor fault
Uneven clothes distribution
while spinning
Poor washing effect
Check whether the type and dosage of
detergent are suitable
Check whether the selected program is
correct
Check whether the clothes weight
exceeds the washer’s rated washing
capacity
Check whether the washer is washing
a single piece of clothing, e.g. woolen
sweater. If so, it is normal
The spinning effect varies with the
type of clothes
Check whether it is for eccentric
protection with few clothes
It is normal that electronic
components are slightly hot
The clothes distribution becomes
imbalanced during washing
Poor water feeding/drainage
conditions result in a longer time
Check whether the drain pipe is bent,
clogged or frozen
Check whether the drain pipe orifice is
100cm higher than the floor
Check whether the filter is clogged
Check whether all the fixing bolts for
transport are removed
Check whether the washer is level (the
washer can be leveled by adjusting the feet)
Check whether the clothes intertwist
Check whether the washer collides with
other objects
Check whether there are foreign bodies in
the washer
Check whether sudden power failure
or water supply cut-off occurs
Check whether the “Start/Pause”
button is pressed
The washer’s program is set with
water discharge time and the
spinning starts after a period of time
Check whether the clothes intertwist
Check whether too much washing
powder was added
Forceless washing
Stop operation
during washing
No spinning
Excessively long
spinning time
Loud noise when spinning
Vibration and
displacement
The clothes are not
spun dry after finishing
the “Spin” program
No water discharge or
slow water discharge
The control panel is
partially hot
The washing does not
end after the preset
delay time
Check whether the washer inclines or shakes
Check whether there are foreign bodies such
as coins and zippers in the washer
Check whether the noise is from the buttons
and zippers of washing
Check whether the noise is from the draining
pump or motor in normal operation
The washer does
not operate
Buttons cannot be
operated
Water leakage occurs
at the water tap
No water inflow or
slow water inflow
Water feeding and water
drainage occurs at the
same time
Abnormal noise
Press the “Temp.” button to
select heating temperature
(--, 30, 40, 50, 60, 90). The
maximum allowable
heating temperature varies
with programs.
“
－
” in the temperature
display area indicates
non-heated washing.
The variable frequency series is set with the “Auto” function. In this mode, press the “Power” button, the washer will turn on and the door will
automatically open; put the clothes to be washed into the washer and close the door, the display screen will display “ ”; press the
“Start/Pause” button, the washer will automatically weigh the clothes and select the optimal washing program, achieving water, electricity
and time saving.
(1) In manual mode, it is recommended that “L-4” or “L-A” be selected for washing many clothes (more than a half drum) and “L-1”, “L-2” or
“L-3” be selected for washing fewer clothes (not more than a half drum).
(2) The “Auto” function is only available for the “Prewash”, “Cotton”, “Synthetic”, and “Wash” programs. For other programs, press this button
to manually adjust the clothes weight level (the level adjustment is not available for the “Wool” program).
If you do not want the washer to weigh the clothes automatically, press the “Auto” button to switch to manual selection of
clothes weight level (the operation is the same as that of non-variable frequency series).
6. Control Panel and Program Description
Press the “Speed”
button to select
spinning speed.
The maximum
allowable spinning
speed varies with
programs.
“Speed” selection
It displays delay time,
remaining washing time,
times of extra rinse,
spinning time, set
temperature, set speed,
clothes weight level, child
lock state, door lock state
and alarm message, etc.
Display screen
“Temperature” selection
“Auto”/“Clothes weight level selection” button
Program knob
Note:
Select the desired
program by turning
this knob.
After turning on the
washer, it
automatically
selects the
program of last
washing.
Press the “Delay” button, its indicator will light up, indicating
this function is selected. The delay time (0.5-24h) increases by
30 minutes each press of “Delay” button. The time will change
continuously if you press and hold this button until you release
it.
The delay time is the end time of washing. For example, 6:00
means the washing ends after 6 hours (the delay time must be
longer than the program’s running time).
This function is not available for the “Spin” program.
“Delay” button
Press the “Extra rinse” button to increase the times of rinse
(at most three times) between the “Rinse” and “Soften”
programs.
When the indicator of “Extra rinse” lights up, it means this
function is selected. Each press of the “Extra rinse” button
increases one time of rinse. P--1~P--3 shows on the
display screen. Press this button again, this function will be
cancelled and the indicator will go out.
This function is not available for the “Wash” and “Spin”
programs.
“Extra rinse” button
Press the “IStrong” button to select or
cancel the function of intensive washing.
This function is to increase washing time,
times of rinse and spinning time of the
main wash stage of the selected program.
When the “Strong” indicator lights up, it
means this function is selected. This
function is not available for the “Rinse” and
“Spin” programs.
“Strong” button
Press the “Start/Pause” button, the
washer will start or pause. When the
washer pauses, the indicator will
flash.
When the washer is turned on and
the “Start/Pause” button is not
pressed, you may open the door by
pressing and holding this button for 2
seconds.
“Start/Pause” button
n o
t t
u b
” r
e w
o P
“
Press the “Power” button to
switch on the washer.
Press this button again and
hold it for 2 seconds to
switch it off.
After switching on the
washer, if any button is not
pressed within 5 minutes, it
will automatically turn off.
Programs Guide
Prewash
Cotton
Synthetic
Wool
Underwear
Sport Wash
Quick
Wash
Rinse
Spin
For washing relatively dirty
cotton fabrics
For washing cotton fabrics
For washing chemical fiber
fabrics
For washing wool fabrics
For washing cotton underwear
For washing sport wear
or children’s clothes
For washing slightly dirty cotton
and chemical fiber fabrics
For washing the clothes only
For rinsing the clothes only
For spinning the clothes only
7. Display Screen
8. Other functions
Numerical display area
Child lock icon
Door lock icon
1. Numerical display area: the delay time, remaining time, times of extra rinse and alarm message, etc. display in this area.
When the washer is in operation, remaining time displays in this area; if you turn on the washer after the selected program
ends, the program time of last washing will display in this area, e.g. 1:28; when the “Delay” function is selected, the delay time
will display in this area, e.g. 6:00; when the “Extra rinse” function is selected, the additional times of extra rinse will display in
this area, e.g. P--1; when the program running is abnormal, alarm message will display in this area, e.g. Err3.
2. Child lock icon: simultaneously press the “Delay” and “Start/Pause” buttons and hold them for 3 seconds, the child lock
function will be activated to avoid changing the selected program by inadvertent touch of buttons; simultaneously press the two
buttons and hold them for 3 seconds again, this function will be cancelled.
3. Door lock icon: this icon will light up when the door is closed and will not show when the door is opened.
Note:
The time shown on the display screen is only for reference and may be slightly different from actual
time due to water temperature and water pressure, etc.
The child lock function will be cancelled when the selected program ends, power failure occurs or the
washer is switched off.
Function
Function
Function
Function
Power-down memory
With the power-down memory function, the washer can
memorize the program’s running state in case of power
failure or loose plug during washing and continue the
formerly selected program after the power supply resumes.
Eccentric protection
When spinning, if the clothes are not evenly distributed, the washer will fluff out
and redistribute the clothes and continue spinning after the clothes distribution
becomes even. If the clothes distribution does not become even within the
specified time, the washer will not spin to avoid abnormal vibration. In this case,
please check the clothes for intertwist and rearrange them, then select “Spin”
program to spin the clothes. When there are few clothes, the washer may not spin
due to eccentric protection. In this case, you can put more clothes into the washer
and make them evenly distributed, then continue spinning. In addition, it is normal
that the program time will prolong because the washer rearranges and fluffs out
the clothes.
Silencing function
Select the “Spin” program, simultaneously press the “Delay” and “Extra rinse”
buttons and hold them for 3 seconds, the beep of all the programs (excluding the
alarm sound) will be silenced and the display screen will show “ ”.
Simultaneously press the two buttons and hold them for 3 seconds again, the
beep of all the programs will resume and the display screen will show “ ”.
Cancel or reselect a program during washing
(1) To cancel the running program, just turn off the washer;
to reselect a program, turn it on again.
(2) To select any additional function when a program is
running, just press the “Start/Pause” button, then select your
desired additional function and finally press the
“Start/Pause” again.
The above operations should be made when the child lock is
not activated.
The method (2) is only available for several function buttons.
Note:
9. Fault Clearance
The following phenomena are not necessarily faults of the washer. Please check against the following table before calling for repair.
If any fault actually exists, please contact our After-sales Service Department and do not repair by yourself. Please pull out the power plug before check.
State
Phenomenon
Solution
State
Phenomenon
Solution
Displayed code
Code meaning
Solution
Displayed code
Code meaning
Solution
e r
o f
e B
n o i
t a
r e
p o
h s
a w
n
e h
W
There is a little water in
the drain pipe and
washer when using the
washer for the first time
It is normal; the water is the remaining
water of factory inspection
Check whether the “Child lock” function is
selected
After starting, to select other programs,
please press the “Start/Pause” button and
then operate
Check whether the height of drain pipe
orifice is within the range of 80cm~100cm
Check whether the drain pipe orifice is
immersed in the water
Check whether the water tap is in proper shape
Check whether the water inlet pipe joint is
installed in place
Check whether the water tap is damaged
Check whether the water tap is turned on and
whether water supply cut-off occurs
Check whether the water inlet valve is clogged (if
necessary, clean the valve)
Check whether the water tap and water inlet pipe
are frozen
Check whether the “Delay” program is selected
Check whether the “Start/Pause” button is pressed
Check whether the water inlet pipe is bent
Check whether the water pressure is too low
Check whether power failure or abnormal
power supply occurs
Check whether the power plug is firmly
inserted into the socket
Check whether the fuse of power supply or the
current breaker is in good condition
Check whether the “Power” switch is turned on
Check whether the water tap is turned on
Check whether the “Delay” function is selected
Check whether the “Start/Pause” button is
pressed
n i p
s
n e
h
W
h s
a w
n
e h
W
n e
h
W
e g
r a
h c
s i d
r e
t a
w
r e
h t
O
Communication fault
Being inconsistent with the
conditions for door opening,
it is not allowed to unlock
the door
and alarms are limited to the variable frequency series.
is limited to the non-variable frequency series.
It is normal that the washer discharges water when or occurs.
Please ask for repair
Note:
Warm tips
To add clothes during washing or to take out clothes
after extended power failure, make sure that the
water level in the drum is properly below the lower
edge of sight glass, the water temperature is below
the drain pipe from its holder and put it down until no
water is drained from the drain pipe, afterwards put
back the drain pipe. Open the filter door at the bottom
of washer, and you will see a pull wire. Take out the
pull wire and gently pull it downwards until you hear a
low sound, the door will open, now you can add or
take out the clothes. Afterwards, reset the pull wire
and filter door.
Pull wire
Note:
Never perform the above operations when the washer is running.
The washer contains recyclable materials. Please properly dispose of them to protect
the environment.
Adding a proper amount of softener may make the clothes soft, eliminate sticking arising
from static electricity and make the clothes easier to be ironed. Excessive soften may
damage synthetic fiber. Please refer to its instructions for correct dosage of softener.
10.Cleaning/Maintenance
Fig. 1
Fig. 2
Fig. 3
Fig. 4
Fig. 5
Filter
Waste pipe
Waste pipe plug
Water container
Please pull out the power plug from the socket before
cleaning and maintenance.
Filter cleaning (once a month as recommended)
(1) After draining the water in the washer, open the filter door by pressing it
down with a flat head screwdriver or a similar tool through the square hole
above the filter door (as shown in Fig. 1).
(2) Hold the plastic pipe plug to pull out the waste pipe, prepare a water
container, remove the plastic plug of waste pipe to drain the remaining
water into the container (as shown in Fig. 2), replace the plastic plug onto
the waste pipe, and finally clamp the waste pipe in original position.
(3) Anticlockwise screw out the filter. It is normal that a little water flows out
at this time (as shown in Fig. 3).
(4) Rinse with clean water (as shown in Fig. 4).
(5) Insert the filter after aligning its convex with the groove of draining pipe,
then clockwise tighten it (as shown in Fig. 5), and finally close the filter door.
Note:
Note:
The filter must be
tightened to avoid
water leakage.
Cleaning of a distributor box
To clean a distributor box, pull it out, gently
press it down and continue to pull it out (as
shown in the figure on the right), remove it,
rinse it with water and reinstall it in place.
Cleaning of the filter screen of water inlet valve
Frequently clean the water inlet pipe joint and
the filter screen of water inlet valve to prevent
them from being clogged by impurities (as
shown in the figure on the right)
Please clean the filter screen of water
inlet valve as shown in the figures below.
①
Take out the filter screen
②
Wash the filter screen
③
Reinstall the filter
screen in place
water inlet
valve joint
Please ask for repair
Press and hold 2seconds
to set door unlocked
Pause
Prewash
Synthetic
Cotton
Wool
Unde wear
r
Sport Wash
Quick
Wash
inse
pin
HW55-B12866NZP
