background image

 

 
 
 
 
 
 

Art. no. 0571207009036 

V15 J05 

 
 

Pellett Stove 

HSP 1.17 

 

Installation and operating instructions 

 

  

Important manufacturer’s instructions

!

 

Please observe the following instructions:  

Quality of wood pellets:  

Depending on the manufacturer there are light, dark, shorter and longer pellets. And the quality of one delivery may 
differ from another even from the same supplier. The standards for wood pellets are becoming more and more strict 
but wood is wood and has its own characteristics regarding ash and clinker.  

Cleaning requirements:  

As  soon  as  you  find  ash  and  clinker  deposits  in  the  cold  combustion  pot,  it  must  be  cleaned. 

See  operating 

instructions! 

If this is not done, there will be more and more clinker. Then the device will no longer be able to ignite 

properly. Pellets may pile up in the combustion pot. In extreme cases, this can reach all the way back to the pellet 
chute.  Backfire  in  the  pellet  container  and  smouldering  in  the  pellet  tank  might  possibly  result. 

This  will  destroy 

your device and is not covered by the guarantee.

  

For maximum working life:  

 

Arrange for commissioning by your trained stove supplier.  

 

Observe  the  daily  check  as  described  and  more  frequently  if  you  have  received  new  pellet deliveries  or  when 
the device is brought back into use after the summer.  

 

Carefully read through all the operating instructions and retain them.

 

 
 Type number: 

 

Summary of Contents for HSP 1.17
































Reviews: