Follow these initial setup steps:
1. Separate bottle and wash it with soap and warm water.
2. Remove plug or obstacles from generator well or adapter.
3. Put bottle back on as removed and hand tighten to seal.
4. With bottle attached rinse out Generator with warm water.
5. Fill bottle with water but leave half inch air space at top.
5. Put cap on bottle top to seal and let stand for 2 - 4 hours.
6. Plug charger cable to USB Port and charge 2 – 4 hours.
7. To use press power once for a 5 min. cycle. (BLUE LED)
8. Press power twice for a 7 minute cycle. (GREEN LED)
9. Press power third time to shut Generator off. (RED LED)
10. LED lights turn off at the end of each timed cycle.
11. Repeat a 5 or 7 minute cycle as desired for more PPM.
12. Release gas pressure building up after every 2 cycles.
13. You can drink water out of the bottle or pour into a glass.
14. Never drink while the unit is operating and keep it level.
15. For best results drink water within minutes of making it.
16. Monitor and empty bottom waste chamber as needed.
17. Allow 5-7 day break-in period before testing PPM levels.
18. Generator Well is shipped wet. This is a NEW Unit.
19. Do not keep Unit plugged and charging once charged.
20. Only use water and preferably at room temperature.
21. If machine leaks, tighten where leaking and check seals.
860-806-9997
Call US For Help or Visit Us On Line
You’re Going To Like
The Way You Feel!
www.H2WaterforLife.com
H2WaterForLife LLC
Morris, Ct. USA Tel: 860-806-9997
[email protected] www.H2WaterForLife.com
No visible bubbles
•
Check power source
•
Remove plug and obstacles
Low PPM levels
when tested
•
Allow 7 days to break-in
•
Keep Unit wet & charged
•
Use 6 ml water sample
Wetness in Generator
•
Units are shipped wet
Battery not charging
•
Call customer support
Unit is leaking
water or gas
•
Check all seals
•
Tighten bottle lid
•
Empty waste chamber
•
Check if missing washer
Unit has an odor or
water is discolored
•
Clean as needed and or
call customer support
Unit is producing less
bubbles than before
•
Clean Unit and or
call customer support
Glass bottle broke
•
Call to order replacement
Water in waste chamber
•
Relieve pressure at lid or
use a more purified water
For All Other or Any Unsolved Problem Call For Support
H2 USB Sport
PRO II
We’re making them
portable and affordable
WARRANTY:
One Year Parts & Labor
H2WaterForLife.com
Global Leader in Hydrogen
Water Makers
Trouble Shooting
Most Advanced, Safe and Effective
Hydrogen Water Making Technology
Never operate Generator without water in bottle.
Keep USB Port sealed by plugging cover back in.
Remove rubber plug from Generator Well before use.
Operate only with any type of potable drinking water.
Not for use with hot, carbonated or other beverages.
Always keep Generator Well wet and never store dry.
Before using, charge battery for at least 2 hours.
Do not place Generator unit in a refrigerator or cooler.
Do not soak or submerge Generator Unit under water.
Hydrogenate only water you will drink in minutes.
Avoid exposing Unit to direct sunlight in sunshine.
Never freeze, use with ice or in cold temperatures.
Never use any chemical cleaners on Generator unit.
Release gas pressure at lid after every 2 cycle times.
Keep away from children, Pets, Heat and Flames.
Do not pull cable from wire or plug with wet hands.
Occasional Cleaning & Maintenance
Clean Generator plates by soaking for 4 hours 1 part white
vinegar or lemon juice diluted by 3 parts water in bottle,
Shake and rinse out generator and bottle with warm water.
Disclaimer: Product is not intended to diagnose, cure,
treat or prevent disease. Seek medical advice if sick.
