Selio
G
- 1 -
1. Introduction
Dear customer:
Thank you for purchasing a DECT Grundig telephone we appreciate your trust in us. This product was
manufactured with the utmost care, should you encounter difficulties during its use. We recommend that you
refer to this user guide. You can also find information on the following site:
http://www.grundig-dect.com
For your comfort and safety, we ask that you read the following paragraph carefully:
Recommendations and safety instructions
Your DECT telephone must not be installed in a humid room (wash-up room, bathroom, laundry
room, kitchen, etc.) unless it is 1.50 m away from a water point or outside. Your telephone must
be operated at temperatures ranging from 5°C and 45°C.
Only use the supplied power adapter, connect it to the base socket according to the installation
instructions provided in this booklet and the indications on the identification label affixed to it
(voltage, current, electric network frequency). As a precaution, in case of danger, the mains
adapters act as a disconnecting mechanism for the 230V power supply. They should be placed
near the device and should be easily accessible.
This telephone was designed for use on the public switched telephone network (PSTN). In case of
a problem you must first contact your reseller. Only use the supplied telephone cord.
Telephone cord is to be connected prior to opening the door.
For your safety, never place your handset on the base station without its batteries, or without its
battery cover. You could get an electric shock.
To prevent your handset being damaged, only use approved rechargeable batteries. Never use
non rechargeable batteries. Make sure to insert the batteries the right way round in your handset's
battery compartment.
Worn out batteries must be discarded according to the recycling instructions presented in this
booklet.
Your DECT telephone has an inside radio range of about 50 metres and up to
300 metres in open space. The immediate presence of metal parts, (of a television for example),
of any electric appliance may result in range reduction.
In areas where storms are frequent, we recommend that you protect your telephone line using a
surge protection device.
This equipment does not function in the case of an electric network shutdown: for
emergency calls, it is recommended to use another unit during power cuts.
The CE marking certifies that the product meets the essential requirements of Directive 1999/5/CE
of the European Parliament and of the Council pertaining to microwave radio equipment and
telecommunication terminal equipment, for the safety and health of users, for electromagnetic
interference. Furthermore, it efficiently uses the frequency spectrum attributed to ground and
spatial communication to prevent damaging interference.
The declaration of compliance may be looked up on the
www.grundig-dect.com
site or can be
obtained from the following address:
Sagem Communications
- Customer relations department
4, rue du Petit Albi - 95800 Cergy Saint-Christophe - France
Selio
G
- 2 -
2. Before you begin
Make sure your package includes the items:
x
Base
unit,
x
Handset,
x
One battery compartment cover,
x
Handset
battery,
x
Telephone line cord,
x
Two
rechargeable
batteries,
x
AC power supply.
In the case of purchasing a pack duo or trio, you will find in addition for each additional handset:
x
A handset charger,
x
One battery compartment cover,
x
Two
rechargeable
batteries.
2.1. Digital security system
Your cordless phone uses a security system to provide protection against false ringing,
unauthorised access and charges to your phone line.
When you place the handset in the base, the unit verifies its security code. After a power cut or
replacing batteries, you must leave the handset on the base station for about 20 seconds to
reset this code.
2.2. Installing the phone
Power socket
Telephone socket
+
-
+
-
batteries
1.
Insert the batteries one by one and the right way round as indicated by their polarities in the
battery compartment.
2.
Put the compartment door back on.
3.
Plug the power supply cord into AC outlet and the other end into the power jack on the base
bottom. The device gives off an aural signal.
4.
Place the handset in the base station to charge for 15 hours prior to first use. if you don’t
properly charge the phone, battery performance will be compromised.
5.
Plug one end of the telephone line cord into the modular wall phone jack and the other end
into the jack on the base (as shown in the illustration).
6.
Once the batteries are recharged, press
key, you can hear dial tone.
Selio
G
- 3 -
Only use the supplied power adapter, connect it to the base socket according to the
installation instructions provided in this booklet and the indications on the identification
label affixed to it (voltage, current, electric network frequency). As a safety measure, you
can use the power adaptors to cut off the 230V current in case of danger. They must be
located near to the device, and must be easily accessible.
2.3. Handset keys
INT
Internal call
Microphone
Earpiece
Mute the microphone /
Correction / Cancel
Talk off /
Switch handset on/off
Recall/Flash
Screen
Navigation key up /
Access to dialled number
Access to menu /
Validadate
Talk on
Activate, deactivate keypad lock
Navigation key down /
Access the caller list
inserting pause
2.4. Base Station
Base button
Pressed briefly:
- telephone set paging.
Held down (4 seconds minimum):
- telephone set registration.
Handset location
Selio
G
- 4 -
2.5. Quick guide to handset display icons
Signal strength
icon (blinking when no signal or the signal strength is weak).
Call
Handset ringer muted.
Received call list
(appears when a new call is in the caller list).
Memory
.
Battery charge state
(
:Full;
: Flat; blinking during charging).
If the battery charge state displays
, this means that your battery level is low and
you can no longer use the handset number keypad. In this case, make sure to place
the handset back on its base station to recharge the batteries.
3. Menu structure
phonebook
add entry
modify entry
delete entry
delete all
settings
handset name
handset tone
language
auto answer
clock / alarm
date / time
alarm
alarm tone
advanced set
pin code
registration
de-register
phione reset
flash time
base tones
Selio
G
- 5 -
4. Calls
4.1. Cordless phone basics
4.1.1. Make a call
Ensure that the handset is switched on.
1. Press the Talk key
, you will hear the dialling tone and the display will show you the
phone icon
.
2. Enter the phone number. The number is dialled.
- OR -
1. If the AUTOMATIC PICKUP function is activated, take the handset off the base station.
2. To end the call, press
or place handset on the base station.
4.1.2. Answering a call
(Refer to paragraph 8.3 page 12)
1. When the phone rings, press the
key to answer the call.
- OR -
1. If AUTO TALK MODE is ON, pick up the handset from the base station to answer.
2. Ending a call press
key or place the handset in the base station.
4.1.3. Handset volume
You can adjust the volume of what you hear through the handset at any time by pressing
or
key. You will hear a beep with each key press. You will hear a double beep when you
reach the highest or lowest setting.
4.1.4. Caller timer
After you press
Talk
key
on the handset, the built-in call timer shows in the display (after 20
seconds) and counts the length of time of the call on minutes and seconds.
4.1.5. Auto talk off
Placing the handset in the case cradle while the handset is off the hook (during a call)
automatically hangs up the handset.
4.1.6. Ending a call
To end a call press
. The timer remains displayed on the screen for 4 seconds.
You can, however, return on the screen saver by pressing
.
4.1.7. Redialling a call
The last five numbers you have dialled can be quickly redialled.
Redialling from Standby Mode:
1. Press
key. The phone number that was last dialled appears on the display.
2. Press
the
or
key to review redial telephone list. (You can select to redial your last
five numbers called).
3. Press key to dial out the number.
Selio
G
- 6 -
4.1.8. Microphone mute function
During a call you can switch OFF the microphone. The call is placed on hold.
-
Enable MUTE function
: Press the
key during a call. The display
shows "
Mute
". Your correspondent will not be able to hear you.
-
Disable MUTE function
: Press the
key to continue the call.
4.1.9. Recall / Flash
Press the
key to access line transfer offered by PABX or call waiting provided by telephone
Company.
4.1.10. Temporary tone
In pulse dialling, you can use temporary tone dialling to temporarily access touch-tone service
offered by banks.
1. Press
the key after call is answered.
2. Press the number key and follow the voice instructions.
3. After you hang up, the phone automatically returns to dial pulse (rotary) service.
4.1.11. Paging the handset
To locate a misplaced handset:
Press
on the base station, the "
paging
" icon flashes until you press the Call key
. Press
the Call/End key
to mute the aural signal.
4.2. Calling line identification presentation (CLIP)
This CLIP phone stores and displays CLIP information provided by your local telephone
company.
You must subscribe to CLIP service in order to use this unit.
If you have not subscribed to CLIP service or if the caller number is «suppressed», the display
shows unknown.
Caller ID call waiting is not working in Pulse dialling mode.
4.2.1. Caller list
CLIP of incoming Call are stored in the CALLER LIST menu.
When you enter the CALLER LIST menu, the display will show icon
.
The list contains the numbers of the last 40 contacts call lasted.
Note !
If the number is too long (more than 12 digits), the screen will not show the number
in full.
Press
key to go to last number page for CID length.
4.2.2. Display of numbers not available
Unavailable
: you are not in same area as your contact.
withheld
: your contact does not want their number to be displayed.
Selio
G
- 7 -
4.2.3. Accessing the list of calls
1. Press
ҏ
or
ҏ
to access the list of calls made or received. The display shows the recent
caller phone number (up to 12 digits).
2. Press
the
or
key through the caller List.
If you press the key
, the incoming call date and time are displayed. This function only
works if you have set the date and time on your base station as described in this manual
user. If the list is empty, the screen displays "
no entries
".
If the number is already stored in your phonebook, the name of the person in question is
displayed.
4.2.4. Calling back a caller
1. Press
the
key to enter the caller list menu.
2. Press
the
or
key to select a call record.
3. Press
the key to dial the number.
4.2.5. Deleting caller list record
1. Press
the
ҏ
key to enter the caller list menu.
2. Press
the
or
key to select a call record.
3. Press
key.
To delete the current record :
- Select
"
delete entry
" using the
or
key.
-
The selected number is deleted. You will hear a confirmation tone
To delete the entire Caller list :
- Select
"
delete all ”
using the
or
key.
A confirmation screen appears :
-
If you do not wish to delete the current record, press
.
-
To delete the current record, press
.
4. The record or the entire Caller list is deleted. You will hear a confirmation tone.
4.2.6. Storing memory from the caller list
1. Press
or
. The list of calls made or received is displayed.
2. Use
or
to select the desired caller number.
3. Press key, then select "
add entry
". press
.
4.
Enter the name of the entry. Press
. The number is displayed.
5. Press to confirm the number.
The entry is stored in the phonebook. You will hear a confirmation tone.
Selio
G
- 8 -
5. Using the Multi-Handset capabilities
These functions are used for handset management when two or more handsets are registered
on the same base.
5.1. Intercom Call/Intercom
1. Press
the
INT
key on the handset.
-
If your installation has two handsets, the second handset is directly called, and "
int
"
followed by the handset number are displayed on the screen.
-
The display shows the " " icon and the number of all registered handsets.
-
Enter the desired handset number or press the
key if you want to call all
handsets. The handset(s) ring(s).
2.
On the called handset, press the
key to answer.
5.2. Answering an internal call
1.
The ring melody from an internal call is different from an external call. "
int
" and the calling
handset number appear on the screen. " " is blinking.
2. Press
the key to answer. The " " stop blinking.
3.
Ending an internal call press the
key.
5.3. Call management
5.3.1. An external and an internal call
Transfering an external call
to another handset registred on same base
You can transfer an outside call to another handset registered on the base station.
During a call, press
INT
. The external user is put on hold.
Enter the internal call number. When the user answers, you can announce the call.
Press the
key to transfer the call.
Note!
To switch from one call to another, press and hold down the
INT
key until an aural
signal is heard.
Note!
If the called handset does not answer, press
INT
to take back the call.
Making conference calls (3-way conversation)
You can connect one external call to two handsets registered at the base station. All users can
talk and listen simultaneously:
1. Press
INT
key. The external user is put on hold.
2. the internal call number. Wait until the internal user answers.
3. Press and hold down the key
to start the three-way conference.
5.3.2. Two outside calls
Taking a second call while you are already on line
During a call, a beep is emitted by your operator to inform you that a second call is on hold. A
screen displays the number of this second caller on hold.
Press
to take back this new call.
Your first contact is put on hold and you can talk with the second caller.
Selio
G
- 9 -
Making a second call while you already on line
During a conversation, press
then dial the number to be called.
The call in process is then put on hold and you can take the second call back.
Switching from one call to the other
To switch from one call to the other, press
then the key
.
The call in process is then put on hold and you can take the second call back.
Ending one of the two calls
To end one call and continue with the other, press
then the key
.
The call in process is then ended finally and you take the second call back.
To set up a 3-way conference (the 2 calls and yourself)
During a conversation, press
then the key
.
You can then talk with the 2 contacts at the same time.
To end the 3-way conference, press the red key
.
6. Phonebook
You can store 50 phonebook entries in your phonebook.
Each phonebook entry can contain the name of your contact which can be a maximum of
12 characters long (spaces included), your contact's telephone number up to 24 digits.
6.1. Dialling a memory number
1. Press
key.
2. Press
the
or
key to view the phonebook locations.
3. Press key. The display number is dialled.
6.2. Storing a memory
1.
Enter the phone number of the entry to be created using handset keys. To delete an
incorrectly entered digit. Press
.
2. "
add enty
" appears on the screen, press the key again
.
3.
Enter the name of the entry. Press the key
to confirm the name entered.
The entry phone number is displayed with the cursor placed at the end of the line.
4.
Press the key
to confirm the number displayed.
The entry is stored in the phonebook. You will hear a confirmation tone.
6.3. Editing a memory
1. Press , "
phonebook
" appears on the screen. Press
.
The list of phonebook entries is displayed in alphabetical order.
2.
Select the entry to be changed using
or
.
Selio
G
- 10 -
3. Press .
Using the
or
key, select "
modify entry
". Press
. The name entry screen is
displayed with the cursor placed at the end of the line:
- The information is accurate. Press
key.
- To correct the name, press
key to delete characters.
- Enter the new name and press
key.
4. You will then enter the number screen and the cursor will be at the end of the number:
- The information is accurate. Press
key.
- To correct the number, press
key to delete the numbers.
- Enter the new number and press
key.
5. The entry is then modified and you will hear a confirmation tone.
6.4. Deleting a memory / the whole phonebook
1. Press , "
phonebook
" appears on the screen. Press
.
The list of phonebook entries is displayed in alphabetical order.
2.
Select the entry to be deleted using
or
. Press
.
- To delete the entry, select "
delete entry
" using the
ҏ
or
ҏ
key.
- To delete the entire phonebook list, select "
delete all
" using the
ҏ
or
ҏ
key.
3.
A confirmation screen appears.
- If you do not wish to delete the entry, press
.
- To delete the entry, press
key.
4.
One phonebook entry or the whole phonebook is deleted. You will hear a confirmation tone.
6.5. Inserting a pause
You can insert a pause in the dialling sequence. Wait for a dial tone before you press
.
Press and hold
key during edit mode to inset the pause. The display shows an
’’
P
’’.
7. Time and alarm setting
7.1. Time and date
1. Press , select "
clock / alarm
" using the
or
key, Press
.
2. Using
the
or
key, select "
date/time
". Press
.
3.
A screen displays the current date DD/MM format.
Enter the new date and press the key
.
Dépliant LU 253106070A Selio EN_UK.fm Page 1 Lundi, 28. juillet 2008 11:02 11
