2
The US Consumer Product Safety Commission (CPSC) estimates that about 100 000 playground equipment-related injuries resulting
from falls to the ground surface are treated annually in US hospital emergency rooms. Injuries involving this hazard pattern tend to be
among the most serious of all playground injuries, and have the potential to be fatal, particularly when the injury is to the head. The
surface under and around playground equipment can be a major factor in determining the injury-causing potential of a fall. It is
self-evident that a fall on to a shock-absorbing surface is less likely to cause a serious injury that a fall onto a hard surface. Playground
equipment should never be placed on hard surface, such as concrete or asphalt, and while grass may appear to be acceptable, it may
quickly turn to hard-packed earth in areas of high traffic. Shredded bark mulch, wood chips, fine sand or fine gravel are considered to
be acceptable shock absorbing surfaces when installed and maintained at a sufficient depth under and around playground equipment.
Table B. 1 lists the maximum height from which a child would not be expected to sustain a life-threatening head injury in a fall on to
four different loose-fill surfacing materials if they are installed and maintained at depths of 150mm, 225mm and 300mm.
However, it should be recognized that all injuries due to fall cannot be prevented, no matter what surfacing material is used.
It is recommended that a shock absorbing material extend a minimum of 1800mm in all directions from the perimeter of stationary
equipment such as climbing frames and slides. However, because children may deliberately jump from a moving swing, the shock
absorbing material should extend in the front and rear of a swing a minimum distance of twice the height of the pivot point measured
from a point directly beneath the pivot on the supporting structure.
This information is intended to assist in comparing the relative shock-absorbing properties of various materials. No particular material is
recommended over another. However, each material is only effective when properly maintained. Materials should be checked
periodically and replenished to maintain correct depth as determined necessary for the equipment in question. The choice of a material
depends on the type and height of the playground, the availability of the material in a particular area, and its cost.
This information has been extracted from the CPSC publications ‘Playground Surfacing – Technical Information Guide” and Handbook
for Public Playground Safety”.
Consumer Information sheet for Playground surfacing materials
Maximum fall height for this product is 3 ft / 904 mm
Table B.1 – Fall height in millimeters from which a life-threatening head injury would not be expected
Type of Material
Double shredded bark mulch
Wood chips
Fine sand
Fine gravel
Depth of surfacing material
150
mm
225
mm
300
mm
1800
1800
1500
1800
3000
2100
1500
2100
3300
3600
2700
3000
¹This information has been extracted from the CPSC publications “Playground Surfacing – Technical Information Guide” and “Handbook for Public Playground Safety.” Copies of
these documents can be obtained by sending a postcard to the: Office of Public Affairs, U.S. Consumer Product Safety Commission, Washington, DC 20207 or by calling the toll
free hotline: 1-800-638-2772.
Choose a level location for the equipment. This can reduce the likelihood of the play set tipping over and loos-fill surfacing materials washing away during heavy rains.
Locate bare metal platforms and slides out of direct sunlight to reduce the likelihood of serious burns. A slide that faces north will receive the least direct sunlight.
Provide enough room so that children can use the equipment safely.
These items can cause death by strangulation.
Information on Playground surfacing materials¹:
Select Protective Surfacing – One of the most important things you can do to reduce the likelihood of serious head injuries is to install shock-absorbing protective surfacing under
and around your play equipment. The protective surfacing should be applied to a depth that is suitable for the equipment height in accordance with ASTM Specification F 1292.
There are different types of surfacing to choose from; whichever product you select, follow these guidelines:
Loose-Fill Materials:
Maintain a minimum depth of 9 inches of loose fill materials such as wood mulch/chips, engineered wood fiber (EWF), or shredded/recycled rubber mulch for equipment up to 8 feet
high; and 9 inches of sand or pea gravel for equipment up to 5 feet high. NOTE: An initial fill level of 12 inches will compress to about a 9 inch depth of surfacing over time. The
surfacing will also compact, displace, and settle, and should be periodically refilled to maintain at least a 9 inch depth.
Use a minimum of 6 inches of protective surfacing for play equipment less than 4 feet in height. If maintained properly, this should be adequate. (At depths less than 6 inches, the
protective material is too easily displaced or compacted.)
NOTE: Do not install home playground equipment over concrete, asphalt, or any other hard surface. A fall onto a hard surface can result in serious injury to the equipment user.
Grass and dirt are not considered protective surfacing because wear and environmental factors can reduce their shock absorbing effectiveness. Carpeting and thin mats are
generally not adequate protective surfacing. Ground level equipment – such as a sandbox, activity wall, playhouse or other equipment that has no elevated play surface – does not
need any protective surfacing.
Use containment, such as digging out around the perimeter and/or lining the perimeter with landscape edging. Don’t forget to account for water drainage.
Check and maintain the depth of the loose-fill surfacing material. To maintain the right amount of loose-fill materials, mark the correct level on play equipment support posts. That
way you can easily see when to replenish and/or redistribute the surfacing.
Do not install loose-fill surfacing over hard surfaces such as concrete or asphalt.
Poured-In-Place Surfaces or Pre-Manufactured Rubber Tiles – You may be interested in using surfacing other than loose-fill materials – like rubber tiles or poured-in-place surfaces.
Installations of these surfaces generally require a professional and are not “do-it-yourself” projects.
Review surface specifications before purchasing this type of surfacing. Ask the installer/manufacturer for a report showing that the product has been tested to the following safety
standard: ASTM F1292 Standard Specification for Impact Attenuation of Surfacing Materials within the Use Zone of Playground Equipment. This report should show the specific
height for which the surface is intended to protect against serious head injury. This height should be equal to or greater than the fall height – vertical distance between a designated
play surface (elevated surface for standing, sitting, or climbing) and the protective surfacing below – of your play equipment.
Check the protective surfacing frequently for wear.
Placement – Proper placement and maintenance of protective surfacing is essential. Be sure to:
Extend surfacing at least 6 feet from the equipment in all directions.
CONSUMER INFORMATION
No. 2036
Ages: 1½ - 4y
Climb N Explore Play Gym
INSTRUCTION MANUAL
1
SAFETY INSTRUCTIONS
Observing the following statements and warnings to reduce the likelihood of serious or fatal injury.
• DO NOT allow children to play on this product until it is completely installed.
• DO NOT allow children to stand, walk close to, behind, in front of, or between moving product. Instruct children to keep a safe distance away.
• DO NOT let children use this product in any manner other than intended.
• Dress children appropriately while on and around this product. Use well-fitting shoes that do not have slippery soles. DO NOT allow children to wear
ponchos, scarves, hoods, jewelry, loose shoes, loose-fitting clothing, neckties, clothing with loose strings and/or clothing that might be potentially
hazardous while using this product.
• Instruct children to remove their bike or other sports helmet before using this product.
• Make sure all parts are securely snapped together before use.
!
CAUTION:
• Warning. Only for indoor and outdoor domestic use. This product is designed for normal residential use only, and is not intended for use in schools,
parks, day care centers, nurseries, or other public places.
• Warning. This product is intended for use by children ages 1½ - 4 years.
• Warning. Maximum weight limit: 50 lbs (23 kg) on each individual play. Limit 1 child at any one time.
• Adult assembly required. Phillips / cross-headed screwdriver (not included) required during assembly.
• Instruct children not to use product until properly assembled.
• Recommend to place the activity toy on a level surface at least 2 m (6.5 feet) from any structure or obstruction such as a fence, garage, house,
overhanging branches, laundry lines or electrical wires.
• On-site adult supervision is required for children of all ages at all times when on or around this product. Never leave children unattended.
• Slide feet first. One (1) child at a time.
• When the slide is exposed to direct sunlight, check the temperature on the product surface. If the slide chute is too hot, pour cold water on the slide
chute until it cools and wipe dry before giving it to children.
• Use only the balls provided with this unit.
• It is recommended that the slide be place in a position unlikely to injure child’s eyes with respect to sun.
CHOKING HAZARD - Small parts. This product contains small parts and sharp points which are necessary for assembly. Prior to or during
assembly of this product, keep all components out of children’s reach. Small parts pose a choking hazard to children under 3 years of age.
DO NOT DISCARD: IMPORTANT LITERATURE. KEEP THESE INSTRUCTIONS FOR FUTURE REFERENCE.
OBSERVE ALL SAFETY WARNINGS AND CAUTIONARY STATEMENTS TO REDUCE THE RISK OF SERIOUS OR
FATAL INJURY.
TO AVOID SERIOUS INJURY: DO NOT install this product on a hard surface. A fall onto hard surface could
result in a head or other serious injuries. Never place on concrete, asphalt, wood, packed earth or other hard surfaces. Carpet over
hard floors may not prevent injury.
!
WARNING:
• The owner of this product shall be responsible for maintaining the legibility of the warning labels.
• Check all coverings for bolts and sharp edges and replace when required.
• Replace defective parts in accordance with the manufacturer’s instructions.
• Please check the unit twice monthly during the usage season for tightness, and tighten as required. It is particularly important that this procedure be
followed at the beginning of each season and monthly thereafter for evidence of deterioration. Replace as needed. If not checked regularly, parts
can be loose or missed and components can become detached and cause injuries.
• DO NOT allow children to climb or to play when the product is wet. It may be slippery when wet.
• DO NOT leave this item exposed to strong wind and inclement weather.
• Clean the slide regularly with soapy water in order to avoid a build up of static electricity.
• Discard all packaging properly after unit has been assembled.
• At the beginning of each play season:
- Tighten all hardware.
- Reinstall any plastic parts, that were removed for cold season.
- Check all protective coverings on bolts, pipes, edges, and corners. Replace if they are loose, cracked or missing.
- Check metal parts for rust. If found, sand and repaint using a non lead-based paint meeting the requirements of 16 CFR 1303.
- Rake and check depth of loose fill protective surfacing materials to prevent compaction and to maintain appropriate depth. Replace as necessary.
• Twice a month during play season:
- Tighten all hardware.
- Check all protective coverings on bolts, pipes, edges, and corners. Replace if they are loose, cracked or missing.
- Rake and check depth of loose fill protective surfacing materials to prevent compaction and to maintain appropriate depth. Replace as necessary.
• At the end of each play season or when the temperature drops below 32°F/0°C:
- Rake and check depth of loose fill protective surfacing materials to prevent compaction and to maintain appropriate depth. Replace as necessary.
- Remove the play gym and store indoor. In extreme cold weather, plastic materials lose resilience and may become brittle and crack upon impact.
• Never use pliers to tighten up screws – these can cause damages to both the paintwork and the special anti-corrosion painting.
• Tighten all nuts and bolts securely. Replace as necessary. If not checked regularly, bolts can be loose or missed and components can become
detached and cause injuries.
• When the time comes to disassemble and dispose of this playground unit, please completely disassemble the unit and discard of it in a safe place
and manner so as not to present any hazard to any individual.
• NEVER attach any materials that are not specifically designed for use with this playground unit, such as (but not limited to) jump ropes, clotheslines,
pet leashes, cables and chains. These pose potential strangulation hazards.
CARE AND MAINTENANCE
GB
GB
