background image

P1

mz-8 HoTT 

 
◎  GRAUPNER   
8th  F,  202  Dong,  Chunui  Techno-Park  II,  202,Chunui-
Dong, Wonmi-Gu,   
Bucheon-Si, Gyeonggi-do, SOUTH KOREA. 
TEL: 

070-7863-3675 FAX 

070-7863-3670

 

E-mail: 

[email protected]

 

 
 
 
FUNCTION 

 

 

 

 

 

Main function and Channel 
Basic 4 Channels and added 6 Channels. 
6 Channel is as below. 
 
① LED : ON / OFF   
-> CH8    1100us / 1900us  

 

 
② SPEED : Attitude mode / Rate mode 

 

   

-> CH5    1100us / 1900us  

 

 
③ SNAP : Taking pictures  

 

   

-> CH9    1100us   (1500us nothing) 
 
④ RECORD : Film movies  

 

 

  -> CH9    1900us 

 

 

 

 

 
⑤ FLIP : Use the button on top left of image (360° FLIP) 
-> CH10    1100us / 1900us 

 

 

now channel  10, later channel 7, (Alpha 150 not active 
in autopilot mode as soon as GPS is connected it will be 
channel 6 coming home function)   
 
⑥ 3D / EASY : Use the button on top right of image 
(180° revolution and additional function) 

 

 

-> CH6    1100us / 1900us 
CH6,  when  AKRO3D  is  adjusted  in  the  receiver,  for 
normal  flight  mode  with  GPS  (Alpha  150)  it  will  be 
autopilot function 
 

 

 

 
 

 
 

 
 

⑦ 2.4GHz Quad with 6-Axis Gyro   

 

 

 

 
 

 
 

 

⑧  
 
 

 
 

     

You  can  attach  camera  and  video  module  by 

choosing  option.  You  can  take  a  video  on  the  radio 
using Photo & Video button. 

 
 
mz-8 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

 
 

Frequency band 

2400MHz ~2483.5 MHz 

Modulation 

FHSS 

Transmission output 

about 1mW 

Temperature range 

-10 … +55 ℃ 

Antenna 

Monopole Antenna 

Battery 

AA Size x 3 pcs 

Operating voltage 

3.6 … 4.8V 

Output voltage 

about 50mA 

Dimension 

151 x 134 x 63.7 mm 

Weight 

about 260g (Incl. battery) 

Summary of Contents for MZ-8







Reviews: