MBVC***1
BLOWER CABINET
INSTALLATION INSTRUCTIONS
Contents
is a registered trademark of Maytag
Corporation or its related companies and is used under license. All rights reserved.
Introduction
............................................................................ 2
Electrostatic Discharge (ESD) Precautions ............................
2
Checking Product Received ......................................................
2
Replacement Parts ...................................................................
2
Ordering Parts ........................................................................
2
Important Safety Instructions ..............................................
2
Recognize Safety Symbols, Words, and Labels .......................
2
General Information ...............................................................
3
Features
.................................................................................... 3
Achieving Less Air Leakage: ......................................................
3
Clearances And Accessibility ...................................................
3
Insulation ................................................................................
3
Installation Instructions ........................................................
4
Blower with Cased Evaporator Coil Installation ...................
4
Upflow Installation ................................................................
4
Counterflow Installation .......................................................
4
Horizontal Installation ..........................................................
4
Counterflow and Horizontal Applications ............................
5
Electrical Connections ............................................................
5
208/230 Volt Line Connections ................................................
5
Low Voltage Wiring .................................................................
5
Operation on 208 Volt Supply ..................................................
6
24 Volt Thermostat Wiring .....................................................
6
CoolCloud HVAC Phone Application ........................................ 6
Quick Start Guide for Communicating Outdoor Units .......... 6
Charging .................................................................................. 7
Electric Heat Kit Testing .......................................................... 8
Quick Start Guide for Non-Communicating Outdoor Units .. 8
Charging ..................................................................................
9
Electric Heat Kit Testing ..........................................................
9
Dehumidification ..................................................................... 9
Auxiliary Alarm Switch ........................................................
10
7-Segment Display and Push Buttons ....................................
10
Accessory Control .................................................................
10
Ramping Profiles ...................................................................
11
Electric Air Cleaner ...............................................................
12
Troubleshooting ...................................................................
12
Troubleshooting Matrix .......................................................
13
Push Button Menus ...............................................................
15
System Status Display .............................................................
17
Airflow Label ......................................................................
18
Wiring Diagram ...................................................................
19
Homeowners Routine Maintenance Recommendations ....
20
THIS PRODUCT CONTAINS ELECTRONIC COMPONENTS WHICH REQUIRE A DEFINITE
GROUND. PROVISIONS ARE MADE FOR CONNECTION OF THE GROUND. A DEDICATED
GROUND FROM THE MAIN POWER SUPPLY OR AN EARTH GROUND MUST BE
PROVIDED.
© 2019 - 2020 Goodman Manufacturing Company, L.P.
19001 Kermier Rd., Waller, TX 77484
www.goodmanmfg.com - www.amana-hac.com
P/N: IO-456A Date: February 2020
O
NLY
PERSONNEL
THAT
HAVE
BEEN
TRAINED
TO
INSTALL
,
ADJUST
,
SERVICE
OR
REPAIR
(
HEREINAFTER
, “
SERVICE
”)
THE
EQUIPMENT
SPECIFIED
IN
THIS
MANUAL
SHOULD
SERVICE
THE
EQUIPMENT
. T
HE
MANUFACTURER
WILL
NOT
BE
RESPONSIBLE
FOR
ANY
INJURY
OR
PROPERTY
DAMAGE
ARISING
FROM
IMPROPER
SERVICE
OR
SERVICE
PROCEDURES
. I
F
YOU
SERVICE
THIS
UNIT
,
YOU
ASSUME
RESPONSIBILITY
FOR
ANY
INJURY
OR
PROPERTY
DAMAGE
WHICH
MAY
RESULT
. I
N
ADDITION
,
IN
JURISDICTIONS
THAT
REQUIRE
ONE
OR
MORE
LICENSES
TO
SERVICE
THE
EQUIPMENT
SPECIFIED
IN
THIS
MANUAL
,
ONLY
LICENSED
PERSONNEL
SHOULD
SERVICE
THE
EQUIPMENT
. I
MPROPER
INSTALLATION
,
ADJUSTMENT
,
SERVICING
OR
REPAIR
OF
THE
EQUIPMENT
SPECIFIED
IN
THIS
MANUAL
,
OR
ATTEMPTING
TO
INSTALL
,
ADJUST
,
SERVICE
OR
REPAIR
THE
EQUIPMENT
SPECIFIED
IN
THIS
MANUAL
WITHOUT
PROPER
TRAINING
MAY
RESULT
IN
PRODUCT
DAMAGE
,
PROPERTY
DAMAGE
,
PERSONAL
INJURY
OR
DEATH
.
WARNING
PROP 65 WARNING
FOR CALIFORNIA CONSUMERS
Cancer and Reproductive Harm -
www.P65Warnings.ca.gov
0140M00517-A
This device, which was assembled by Goodman Manufacturing
Company, L.P., contains a component that is classified as an
intentional radiator. This intentional radiator has been certified by
the FCC: FCC ID QOQBGM111. And this international radiator has
an Industry Canada ID: IC 5123A-BGM111.
This device complies with Part 15 of the FCC’s Rules. Operation of
this device is subject to two conditions:
(1) This device may not cause harmful interference; and
(2) This device must accept any interference received, including
interference that may cause undesirable operation.
And this device meets the applicable Industry Canada technical
specifications.
The manufacturer of the intentional radiator (model no. BGM111) is
Silicon Laboratories Finland Oy, which can be contacted by calling
617-951-0200. (www.silabs.com)
The FCC responsible party is Goodman Manufacturing Company,
L.P., and may be contacted by calling (713)-816-2500, or at 19001
Kermier RD., Waller TX 77484. (www.GoodmanMFG.com)
This equipment complies with FCC radiation exposure limits. To
ensure compliance, human proximity to the antenna shall not be
less the 20cm during normal operations.
Changes or modifications not expressly approved by the party
responsible for compliance could void the user’s authority to
operate the equipment.
