1
4
1)
2)
3)
4)
Position Rack Bearing Plate (9) through the rear of Aluminum Body (1) into the slot, then push Gear Rack (8)
forward into the front of Aluminum Body (1).
Position the first tooth of Gear Sector (10) engaged with the first tooth of Gear Rack (8) <NOTE: Can use a
screwdriver to adjust Gear Sector (10) position.>, the hole of Gear Sector (10) should align with the front Pivot
Pin hole, install the first Pivot Pin (17) with Pivot Pin Washer (16) and Snap Ring (15) to the front Pivot Pin hole
of Aluminum Body (1). When assembled correctly, the wider section (W) of Gear Sector (10) should face down to
Lower Handle (12) position.
Swing Upper Handle (11) to the front and to position the first tooth of Driving Gear (11) engaged with the first
tooth of Gear Sector (10) <NOTE: Can use a screwdriver to adjust Gear Sector (10) position.>, the hole of
Driving Gear (11) should align with the rear Pivot Pin hole, install the second Pivot Pin (17) with Pivot Pin
Washer (16) and Snap Ring (15) to the rear Pivot Pin hole of Aluminum Body (1).
Reassemble Head (3) back to Aluminum Body (1) firmly.
B
REASSEMBLY:
NOTE: ALWAYS CHECK Fig. E CAREFULLY TO REASSEMBLE.
E.
1)
2)
PROBLEM - Rivet Mandrel can not be inserted into Working Nosepiece (2) or Spent Mandrel can not be ejected
after setting.
CAUSE 1 - Handles (11, 12) are not fully opened.
CORRECTION 1 - Open Handles (11, 12) fully.
CAUSE 2 - Working Nosepiece (2) is loose.
CORRECTION 2 - Tighten Working Nosepiece (2) with service Wrench (18).
PROBLEM - Rivet Mandrel is not gripped or Tool requires more operations than normal to set Rivet.
CAUSE 1 - Jaws (5) are dirty, worn or broken.
CORRECTION 1 - Clean or replace Jaws (5).
CAUSE 2 - Working Nosepiece (2) is loose.
CORRECTION 2 - Tighten Working Nosepiece (2) with service Wrench (18).
F. TROUBLE SHOOTING GUIDE:
When operating, ALWAYS WEAR SAFFTY
GOGGLES TO PROTECT YOUR EYES.
Tool must clear off and eject the Spent
Mandrel from Tool before setting next Rivet.
2017 GOEBEL
C
No.
Part No.
Part Name
1
2-40
2-48
2-64
2-48M
2-64M
2-64T
GO-39-0240
GO-39-0248
GO-39-0264
GO-39-01
Aluminum Body
Nosepiece, for 4.0 mm or
5/32” Rivet
Nosepiece, for 4.8/5.0 mm or
3/16” Rivet
Nosepiece, for 6.0 mm
Nosepiece, for 6.4 mm or
1/4” Rivet
Nosepiece, for 4.8/5.0 mm or
3/16” *Monobolt Rivet
Nosepiece, for 6.4 mm or
1/4” *Monobolt Rivet
Nosepiece, for 6.4 mm or
1/4” *T Rivet
Head, Standard
Jaw Case
No.
Part No.
Part Name
5
6
7
8
9
10
12
13
14
15
16
17
18
19
11
GO-39-11
GO-39-05
GO-39-06
GO-39-07
GO-39-08
GO-39-09
GO-39-10
GO-39-12
GO-39-13
GO-39-14
GO-39-15
GO-39-16
GO-39-17
GO-39-18
GO-39-19
1
4
5
6
7
18
14
19
19
13
8
15
16
17
16
15
15
16
17
16
15
3
2
10
11
Driving Gear
12
2
9
2017 GOEBEL
C
Jaws, 3-pc Type
Jaw Pusher
Jaw Pusher Spring
Gear Rack
Rack Bearing Plate
Gear Sector
Driving Gear & Upper
Handle Assembly
Lower Handle
Name Plate
Drive Pin
Snap Ring
Pivot Pin Washer
Pivot Pin
Wrench
Grip
1) means Wearing Parts or Possible Missing Parts.
2) GO-39 Rivet Tool can set Ø4.8 mm (3/16") & Ø6.4 mm (1/4") *Monobolt Rivets and Ø6.4 mm (1/4") *T Rivet.
3) GO-39 Rivet Tool may install various Nosepieces for different applications on request.
4) GO-39 Rivet Tool can be packed in a Plastic Carry Case or Steel Carry Case on request.
5) *Monobolt Rivet and *T Rivet are the registered trademark of Avdel.
Gear Type Hand Rivet Tool
GO-39
Industrial
Heavy Duty
GO-39-0260
GO-39-03
GO-39-04
GO-39-0248M
GO-39-0264M
GO-39-0264T
2-60
3
4
Lorem ipsum
