1
WO15Z-1 DUPLEX RECEPTACLE
The GoControl™ family of Z-Wave® certifi ed wireless lighting products
(smart LED fi xtures, bulbs, switches, dimmers, outlets, plug-in modules, and
thermostats) and security devices (alert sounder, motion sensor, and door/
window sensor) bring a new level of intelligent wireless capability to commercial
and residential environments.
The Z-Wave wireless protocol is an international wireless standard for remote
home automation, security and other applications. This product can be included
and operated in any Z-Wave network with other Z-Wave certifi ed devices
from other manufacturers and/or other applications. All non-battery operated
nodes within the network will act as repeaters regardless of vendor to increase
reliability of the network.
GoControl Z-Wave products are easy to install, are Z-Wave certifi ed, and allow
dealers to create an integrated wireless network with nearly limitless expansion
and interoperability with security, energy management, home entertainment,
appliances, and more.
Receptacle Confi guration
The WO15Z-1 Receptacle controls the ON and OFF of a load connected to
the controlled outlet
(the bottom outlet, see Wiring Diagram)
.The other
outlet remains powered all the time. A button on the face of the receptacle
is used to add the module to the wireless network and be controlled from the
wireless Controller. With the Wireless Controller, the WO15Z-1 Receptacle can
be turned ON and OFF remotely, and can be included in groups that operate
at the same time (a group can be a single module), and in scenes that set a
lighting mood.
DANGER! SHOCK HAZARD.
Read and understand these
instructions before installing. This device is intended for installation in
accordance with the National Electric code and local regulations in the United
States, or the Canadian Electrical Code and local regulations in Canada. It is
recommended that a qualifi ed electrician perform this installation. Make sure
the total load controlled does not exceed 1800 watts.
For indoor use only. Retain instructions for future use.
INSTALLATION
Wire this receptacle in place of a current receptacle according to the diagram
above. Use copper wire only, or equivalent.
Adding to a network:
See the Wireless Controller operating instructions for details to include this
module under the command of the Wireless Controller.
1.
Prepare the Controller to include a unit to the network, by adding it to a group
(method of adding a node to the network). Refer to Controller instructions.
2.
The WO15Z-1 must be in its permanently installed location. Press the
button on the WO15Z-1 once.
3.
You should see an indication on your Controller that the “DEVICE WAS
INCLUDED” in the network.
✓
NOTE: If you have trouble adding the WO15Z-1 to a group it may be that the
Home ID and Node ID were not cleared from it after testing. You must fi rst
“RESET UNIT” with your controller to remove it from the network. Although
adding it to a group includes it in the network, removing it from a group does
not remove it from the network. If removed from a group, it functions only
as a repeater.
Removing from a network:
The WO15Z-1 can be removed from the network by the Controller/Gateway.
Refer to the Controller operating instructions for details.
1.
Set the Controller into Removal Mode and follow its instruction to delete the
WO15Z-1 from the Controller.
2.
Remove the switch by pressing the button twice.
3.
You should see an indication on your Controller that the “device was
removed” from the network.
BASIC OPERATION
Button (Local Control)
The button on the WO15Z-1 allows the user to turn the load attached to the
controlled outlet ON or OFF.
• Tapping button toggles the load attached ON or OFF.
• Include or exclude the module from the Z-Wave system.
When a Controller prompts to “Send Node ID” or to “Press Button on Unit”,
quickly tap the button once to satisfy those instructions. (Tapping the button
also toggles the load attached ON or OFF).
Remote Control
The WO15Z-1 will respond to BASIC and BINARY commands that are part of
the Z-Wave system. Refer to your Controller’s instructions as to whether your
Controller can transmit those commands.
PRINTER’S INSTRUCTIONS:
INSTR,INSTL,WO15Z-1,GO CONTROL; P/N: 10008915 X3; INK: BLACK; MATERIAL: 20# MEAD BOND; SIZE: 8.500” x 11.000”; TOLERANCE ± .125”; SCALE: 1-1; PAGE 1 OF 2
WO15Z-1
Z-Wave Radio Frequency (RF) Controlled, 120 VAC
15 Amp, Duplex Receptacle, Series 300
NOTE:
This unit must be added to the Network
only where it will be permanently installed.
The proper operation of this node in the
mesh network is dependent on it knowing its location with respect to other nodes. You cannot “test bench” confi gure this unit, then install.
ALWAYS POWERED
OUTLET
CONTROLLED
OUTLET
GROUND
GREEN
WHITE
BLACK
NEUTRAL
LINE 120 VAC
TOTAL LOADS MUST NOT EXCEED
15 AMPS @ 120 VAC
(INCLUDES ALL LOADS PLUGGED INTO
THE RECEPTACLE)
