1 7/8
DISCONNECT POWER BEFORE INSTALLING
DESUNA LA ELECTRICIDAD ANTES DE HACER REPARACIONES
WARNING:
INSTALLATION INSTRUCTIONS
1. Remove cover by removing (2) tamper proof-screws using security wrench
supplied. Pull cover directly toward you.
IMPORTANT
: Save security wrench.
2. Dryers should be placed at least 2 feet (61cm) apart and at least 12” (30cm) from
washbasin. Do not install dryer over washbasin. Automatic dryers should be at least
18” (46cm) above any projection which may interfere with the operation of the auto-
matic sensor.
Hold the backplate to the wall at the suggested mounting height. Measure from bot-
tom edge of
backplate
to the
floor (Ref. Dimension “A”, Fig. 1):
CHILDREN
MEN
WOMEN
(depends on age)
DISABLED
44” (112cm)
42” (107cm)
32 to 42” (81-107cm)
36” (91cm)
3. Mark the locations of the four mounting holes and the conduit entrance location on the
wall. (The conduit entrance is the proper hole diameter for 1/2 inch (13mm) conduit.)
4. Fasten the backplate to the wall where previously marked.
RECOMMENDATION:
Wood wall –
No. 14 (M6) wood screws, 2 3/4” (70mm) long
Cement or brick –
1/4” (M6) stud expansion bolts, 3” (76mm) long
Hollow wall –
1/4” (M6) toggle bolts, length depends on wall thickness
5. Run service wire to the dryer location and connect to lead wires.
IMPORTANT: All units must be supplied with 3 wire service. Use No. 12 or 14 wire
as required by local electrical code. The ground wire must be connected to the dryer
ground screw. Unit must be installed by a qualified licensed electrician.
CONNECT TO A DEDICATED CIRCUIT NOT TO ExCEED 20 AMPS.
Dryers located in shower rooms or other wet locations should be equipped with
ground fault interrupter(s).
6.
Carefully
replace the cover using (2) tamper-proof screws supplied. Apply a bead of
caulk around edges of cover to wall.
GLOBAL DRYER
MFD by AMERICAN DRYER, INC.
12932 FARMINGTON ROAD, LIVONIA, MI 48150, U.S.A.
Telephone (734) 421-2400
GLOBAL DRYER LIMITED WARRANTY
All parts of the
Gx-M/C
models are warranted to the original consumer purchaser
to be free from defects in material and workmanship for a period of five (5) years or
three (3) years for
Gx
models from the date of purchase from manufacturer. Sensor
warranty three (3) years in the U.S.A. All models outside of the U.S.A., one (1) year
including sensor. We will replace FREE OF CHARGE, during the warranty period,
any warranted part which proves defective in material and/or workmanship under nor-
mal installation, use, and service, excluding normal wear. Replacement parts can be
obtained by returning the part, TRANSPORTATION CHARGES PREPAID. You must
notify factory prior to returning part or dryer. Any damage to this dryer as a result of
misuse, abuse, neglect, accident, improper installation, unauthorized repairs, or any
other use violative of instructions furnished by us, WILL VOID THIS WARRANTY. THIS
WARRANTY IS IN LIEU OF ANY AND ALL WARRANTIES, EXPRESS OR IMPLIED,
AND IS LIMITED TO THE REPLACEMENT OF DEFECTIVE PARTS ONLY. LABOR
CHARGES AND/OR DAMAGE INCURRED IN INSTALLATION OR REPLACEMENT
AS WELL AS ALL INCIDENTAL AND CONSEQUENTIAL DAMAGES CONNECTED
THEREWITH ARE EXCLUDED.
O
wner
’
s
M
anual
GX S
eries
H
and
D
ryers
F
or
I
nstallatIon
or
s
ervIce
a
ssIstance
P
lease
c
all
(734) 421-2400
or
I
mPortant
:
H
ave
M
odel
& S
erial
N
o
. r
eady
m
odel
#______ s
erIal
#______
F
igure
1 -
d
ryer
M
ouNtiNg
®
(48mm)
(208mm)
6 3/16
7/8 (22mm) DIA. IN-WALL
& SURFACE CONDUIT
ENTRANCES
MOUNTING HOLES FOR
1/4” (M6) DIA. SCREWS
(227MM)
8 15/16
7/16
(11mm)
7/16
(11mm)
“A”
8 7/16
(214mm)
FLOOR
