GlassCrafters Equalis series Скачать руководство пользователя

Страница: 1 / 16

Frameless By-Pass Shower/Tub Enclosure

Installation Instructions

The following instruction sheet is for the installation of the models:

SHOWER ENCLOSURES: DS-48T-38

45”- 48”w X 76”h

, DS-54T-38

51”- 54’w X 76”h

, DS-60T-38

57”- 60”w X 76”h ,

DS-66T-38

63”- 66”w X 76”h

TUB ENCLOSURES: DT-60T-38

57”- 60”w X 66”h

, DT-66T-38

63“- 66”w X 66”h

All Units are available in three finishes:

Brushed Stainless Steel (BSS), Polished Stainless Steel (PSS), Polished Chrome Aluminum (CHA) or Iron Black (IBK)

Please use extreme care while unpacking and handling your GlassCrafters’ Shower or Tub Enclosure. If you need

replacement parts or have installation questions and to report any damage contact our GlassCrafters’ customer service

team at

[email protected]

or 888-683-1362, Monday thru Friday from 8:00 am to 5:00 pm (EST).

Installation shall be made according to manufacturers’ instructions and drawings .

GlassCrafters recommends the installation be performed by a trained installer.

Revised110/2018

WARNING: TO INSTALL ON CAST IRON, FIBERGLASS, ACRYLIC OR RESIN TUB OR SHOWER BASE

Check with the tub or shower base manufacturer to determine the tooling required.

Shower Enclosure

Tub Enclosure

INSTALLING

THESE UNITS

REQUIRES

2 PERSONS

FOR BEST RESULTS

GlassCrafters recommends the installation be

performed by a trained installer.

SAVE THESE INSTRUCTIONS

FOR FUTURE REFERENCE

EQUALIS Series Frameless By-Pass

Shower/Tub enclosures are also

available with a Return Panel.

Separate Installation Instructions for the

Return Panel are supplied in the Return Package.

GLASSCRAFTERS, INC
193 Veterans Blvd., Carlstadt, NJ 07072

1+(888) 683-1362 -- (Fax) 201-525-1117
[email protected]

Содержание Equalis series

















Результаты поиска

Содержание Equalis series

Отзывы:

Похожие инструкции для Equalis series

Бренды по названию

Популярные бренды

GlassCrafters Equalis series, Руководство по установке

Результаты поиска

Содержание Equalis series

Отзывы:

Похожие инструкции для Equalis series

Бренды по названию

Популярные бренды