Product Display Layout
RECEIVER
RECEIVER LED DESCRIPTIONS
ROOM THERMOSTAT PLACEMENT
Room Thermostat needs to be placed in the room which is used most frequently.
For instance; living room or lounge. Placing the Room Thermostat in a spot that
have air circulation like entrance of a room or side of window should be avoided.
Also anywhere close to heating/cooling units such as radiator, stove and spots
which get direct sun lights would not be suitable. Room Thermostat needs to be
located above the floor 150 cm height. Few trials may be made to find the most
convenient spot.
GENERAL SPECIFICATIONS
SOLARA 330S RF
is a wireless room thermostat. The user can get more
comfortable and economic heating/cooling by adjusting the room thermostat with
the required temperature.
Daily and Weekly Programming
Different Mode Options (Comfort, Economy, Holiday)
Heating Calibration
ON/OFF Control
Wireless Connection
Heating/Cooling Option
TPI Algorithm
Precise Temperature Measurement
SOLARA 330S RF
and EQUIPMENTS
TECHNICAL DATA
Room Thermostat
Receiver
ROOM THERMOSTAT
Button Functions
BATTERY PLACEMENT
Press the screwdriver forward from the space at the bottom of the Room
Thermostat, bend the tabs and separate the front cover. Insert 2 new AAA alkaline
batteries in the battery housing with the correct battery direction. Replace both
batteries at the same time. Align the front part of your Room Thermostat with
corresponding slot on the back, and then push gently until the thermostat snaps
into place.
Low Battery Warning:
When the “
” icon appears on the screen, it means “low
battery warning”. It is recommended to replace the batteries when this warning
appears.
Warning:
When the product is not used for a long period (more than 15 days),
remove the batteries. Otherwise, malfunctions that may occur would be out of
warranty. Please throw your dead batteries into the waste bin for batteries.
RECEIVER PLACEMENT
The important things to note for the Receiver placement are
avoiding physical contact between the Receiver and
heating/cooling unit, and protecting it against materials
such as liquid, dust etc.
The devices should be placed in order to minimize the damage to the received and
transmitted signals by paying attention to the following points;
The devices should not be mounted on metal surfaces.
The devices should not be installed close to electrical cables and electronic
equipment such as computers and television units.
The devices should not be installed near large metal structures or other building
materials using fine metal meshes such as special glass or special concrete.
Distance between the Room Thermostat and the Receiver should not exceed 20
meters or 2 floors.
Receiver must be installed at least 50 cm away from the heating/cooling unit.
RECEIVER SETUP
First, shut down your heating/cooling unit and your heating/cooling unit's power
source with all electrical current (fuse, socket etc.)
As shown in the connection diagram, connect one end of the heating/cooling unit
connection cable to the COM and the other to the NO input of the Receiver.
Connect the other ends of the cable -which you connected to the Receiver- to
room thermostat connection terminal as shown in your heating/cooling unit's
user manual.
You must first connect the Receiver power cable to the Receiver and then to the
fuse which the heating/cooling unit is connected.
After completing the cable connection process, firstly turn on your fuse and then
your heating/cooling unit.
By pressing the Receiver's manual usage button for 2 seconds, you should see
the Orange Light blinking on the Receiver. In this way, after making sure that the
heating/cooling unit is operating, press the same button again for 2 seconds and
see that the Orange LED turns off.
Set up the Room Thermostat to pair the Receiver with the Room Thermostat.
RECEIVER WIRING DIAGRAM
Warning!
Operations within the heating / cooling unit or the electrical installation must be
carried out by professionally qualified persons.
1
2
3
85mm / 125mm / 20mm
3V DC (2 x AAA
alkaline battery
)
o
0.1 C
o
o
(5 C) – (30 C)
1
Year
(2 x AAA)
o
o
(-10 C) – (+50 C)
o
o
(-20 C) – (+60 C)
Dimensions
Operating Current
Temperature Measurement Accuracy
Operating Temperature Range
Battery Life
Operating Temperature
Storage Temperature
Alkaline Battery
Holder
4
Weekly Program Button
Heating & Cooling Option
Mode Button
Temperature Adjustment Button (To Increase)
Temperature Adjustment Button (To Decrease)
On/Off Button – Unlock Button
1
2
3
4
5
6
1
A
A
A
A
A
A
90mm / 90mm / 25mm
230V AC
7A (240VAC –
Resistive
L
oad
)
10A (120VAC –
Resistive
L
oad
)
o
o
(-20 C) – (+60 C)
Dimensions
Operating Current
Relay NO Switching Current
Storage Temperature
Dowels and Screws
Receiver
ENGLISH
generallife.com.tr
DIGITAL ROOM THERMOSTAT
SOLARA 330S RF
USER MANUAL
SOLARA 330S RF
Room Thermostat
2
3
4
5
6
1
2
3
4
5
6
9
11
12
7
10
Hour Indicator
Room Temperature
Economy Mode
Comfort Mode
Holiday Mode
Weekly Program Mode
Day Indicator
Screen Lock
Battery Indicator
Set Temperature
Heating Indicator
- If the Heating Indicator is blinking, the heating unit is working.
- If the Heating Indicator is steady, the heating unit is not working.
Cooling Indicator
- If the Cooling Indicator is blinking, the cooling unit is working.
- If the Cooling Indicator is steady, the cooling unit is not working.
1
2
3
4
5
6
7
8
9
10
11
12
Steady Red
Blinking Green
Steady Green
3 Short Orange Blinking
Steady Orange
3 Short Green Blinking
Blinking Orange
Blinking Red
Receiver has power but Receiver and Room Thermostat
are not paired.
Waiting for pairing signal from the Room Thermostat.
Receiver and Room Thermostat are paired.
Heating/cooling unit is not operating.
Operate the heating/cooling unit signal has reached to
the Receiver.
Heating/cooling unit is operating.
Shut the heating/cooling unit down signal has reached
to the Receiver.
Heating/Cooling unit operates in manual mode.
Receiver did not get any signal from the Room
Thermostat for 22 minutes or longer.
Heating/cooling unit has shut down.
min. 20 cm
4
1
2
3
1-
Manual Operation Button:
Deactivates the
Receiver and allows you to use heating/cooling
unit manually.
2-
Pairing Button:
Allows pairing the Receiver
with the Room Thermostat.
3-
Receiver LED Light
4-Receiver Power Cable Input
5-Heating/Cooling Unit Connection Cable Input
5
8
COM
NO
AC
(230V)
HEATING/COOLING UNIT
PAIRING
THE ROOM THERMOSTAT AND THE RECEIVER
Primarily press the sync button of
the R
eceiver for 2 seconds and see blinking
green light of
the R
eceiver.
While your device is turned off, press and hold the "On/Off" button for 3 seconds.
Press the button until the “
” menu appears.
Press the “Up” or “Down” button of your Room Thermostat while the LED is
flashing green.
If the pairing is successful, the green flashing LED on the
R
eceiver will be steady.
Receiver and Room Thermostat have been paired to each other.
ROOM THERMOSTAT TEMPERATURE CALIBRATION
Temperature sensors which are used in Room Thermostats are highly sensitive.
You may need to calibrate your Room Thermostat if you would like to get the same
temperature values with other thermometers in your living space.
While your device is turned off, press and hold the “On/Off“ button for 3 seconds.
Press the "On/Off" button until the “
” menu appears. In order to see the
desired temperature, set the temperature difference by pressing the
“Temperature Adjustment Buttons”. This value can be arranged between “-8° C"
and “+8° C".
In order to save the settings and exit, press the "On/Off" button until the device
turns off.
Note:
Recommended temperature calibration is “0.0°C”.
FACTORY SETTINGS RESET
Temperature sensors which are used in Room Thermostats are highly sensitive.
You may need to calibrate your Room Thermostat if you would like to get the same
temperature values with other thermometers in your living space.
While your device is turned off, press and hold the “On/Off” button for 3 seconds.
Press the “On/Off” button until
the
“
” menu appears.
While in the “
” menu, select the “
” option by using
the
“Up” or “Down”
buttons and press the “On/Off” button.
Your device will be turned off and reset to factory settings.
KEY LOCK
In the Room Thermostat there is a key lock function to avoid any unintended
contact.
In order to unlock the Room Thermostat's key lock
the
“On/Off” button should be
pressed for 3 seconds. If buttons on Room Thermostat are not touched for 10
seconds, key lock will be reactivated.
DAY AND HOUR SETTINGS
While your Room Thermostat is on, keep pressing
the “
Weekly Program
”
button
for 3 seconds.
At the first screen that appears, hour part will be blinking. You may set the time
with
the “
Up
”
and
“
Down
”
buttons.
After setting the time,
the “
Heating & Cooling Option
”
button needs to be pressed
once. For minute setting, minute part will be blinking. You may set the minute with
the “
Up
”
and
“
Down
”
buttons.
After setting the minute,
the “
Heating & Cooling Option
”
button needs to be
pressed once to set the day of the week.
Monday has set as the first day of the week and indicated with number
“
1
"
.
Numbers indicate the following days respectively 2-Tuesday, 3-Wednesday,
4-Thursday, 5-Friday, 6-Saturday and 7-Sunday
When setting is done, you may exit by pressing the “Weekly Program” button for 3
seconds.
MODE SETTING
Your Room Thermostat has 5 different modes. 3 of them (Comfort, Economy and
Holiday Mode) are preset modes. Other modes are manual mode and weekly
program mode.
In preset modes, temperature values are based on user's choices which have been
set in the beginning. Manual mode allows the Room Thermostat to operate within
the temperature which is required and set directly by user. Weekly Program mode
continues to work according to the weekly schedule determined by the user.
In order to change the temperature values of preset modes:
Press and hold the “Mode” button for 3 seconds while your Room Thermostat is
on.
Comfort Mode temperature value will appear. You may adjust the temperature
value of Comfort Mode by pressing
the
“Up” and “Down” button
s
.
When setting is done, you may adjust the temperature value of Economy Mode
with
the
“Up” and “Down” button
s
by pressing the “Mode” button again.
You may exit
the setting screen by pressing the “Mode” button 3 seconds.
In order to change the manual mode temperature, press the “Up” or “Down” button
while in the main screen. The Room Thermostat will switch to Manual Mode once
pressed
the
“Up” or “Down” button.
You may press the “Mode” button to switch to the other modes.
MODES
PRESET MODES
WEEKLY
PROGRAM
MODE
MANUAL MODE
Comfort
Mode
Economy
Mode
Holiday
Mode
