General International 25-036 Скачать руководство пользователя

Страница: 1 / 20

LATHE NOT INCLUDED

FEATURES

REVISION 3 - JANUARY 13/11
© Copyright General® International 01/2011

Designed for rough bulk material
removal from wood blanks, to make
multiple matching spindles that follow the
profile of an original spindle or a shop
made template.

Extruded aluminum base and carriage.

Smooth hand wheel controlled rack &
pinion system.

High speed steel cutter.

Fits most 12” - 22” floor model lathes with
cast bedways.

SPECIFICATIONS

MAXIMUM DUPLICATING LENGTH
36” (914 mm)

MAXIMUM DUPLICATING DIAMETER
2”~20” (51 ~ 508 mm)

Depending on lathe swing over bed

MAXIMUM DUPLICATING DEPTH
3” (76 mm)

MAXIMUM ORIGINAL SPINDLE DIAMETER
5” (127 mm)

MAXIMUM WIDTH OF TEMPLATE
3” (76 mm)

DUPLICATES FROM
ORIGINAL SPINDLE OR TEMPLATE

MAXIMUM DEPTH OF CUT PER PASS
1/4” (6.35 mm) -

1/8” recommended

* Some manual shaping of fine details and fin-

ish sanding will still be required.

Содержание 25-036





















Результаты поиска

Содержание 25-036

Отзывы:

Похожие инструкции для 25-036

Бренды по названию

Популярные бренды

General International 25-036, Руководство по установке и эксплуатации

Результаты поиска

Содержание 25-036

Отзывы:

Похожие инструкции для 25-036

Бренды по названию

Популярные бренды