background image

1

49-50229-1 03-08 JR

Installation

Indoor Direct Vent Tankless Water Heater

Instructions

Models GN75DNSRSA, GN94DNSRSA, GP94DNSRSA

Questions? Call 888.HOTWTER (888.468.9837) or Visit our website at ge.com

BEFORE BEGINNING INSTALLATION

Read these instructions completely and carefully.

IMPORTANT

Save these instructions

for local inspector’s use.

IMPORTANT

Observe all governing

codes and ordinances.

Note to Installer –

Be sure to leave these

instructions with the Consumer.

Note to Consumer –

Keep these instructions

for future reference.

• Proper installation is the responsibility of the

installer.

• Product failure due to improper installation

is not covered under the Warranty.

Recognize this symbol as an indication
of Important Safety Information!

WARNING:

Read entire manual. Failure to follow all guides and rules could cause personal

injury or property damage.

• Check with your state and/or local public works department for plumbing codes. You must follow their

guides as you install the Water Heater.

NOTE: Failure to comply with these installation instructions will void the product warranty, and the
installer will be responsible for any service, repair or damages caused thereby.

SAFETY PRECAUTIONS

WARNING:

If the information in these

instructions is not followed exactly, a fire or explosion
may result, causing property damage, personal injury
or death.

FOR YOUR SAFETY!

– Do not store or use gasoline or other

flammable vapors or liquids or other
combustible materials in the vicinity of this
or any other appliance. To do so may result
in an explosion or fire.

– WHAT TO DO IF YOU SMELL GAS

• Do not try to light any appliance.
• Do not touch any electrical switch;

do not use any phone in your building.

• Immediately call your gas supplier from a

neighbor’s phone. Follow the gas supplier’s
instructions.

• If you cannot reach your gas supplier,

call the fire department.

• Do not return to your home until authorized

by the gas supplier or fire department.

– Improper installation, adjustment, alteration,

service or maintenance can cause property
damage, personal injury or death. Refer to
this manual. Installation and service must
be performed by a qualified installer, service
agency or the gas supplier.

• This water heater must be vented outdoors

using approved ducting materials.

• Service information and wiring diagram are

located behind front panel.

• Service must be performed by a qualified

service agency.

• This appliance must be properly grounded and

installed as described in these instructions.

FOR INDOOR APPLICATIONS ONLY

Summary of Contents for GN75DNSRSA





























Reviews: