GE GE Profile JDS28DNWW Installation Instructions Manual Download

Page: 1 / 24

31-10829

GE10-11

BEFORE YOU BEGIN

Read these in struc tions care ful ly and completely.

•

IMPORTANT

—

Savetheseinstructionsfor

localinspector’suse.

•

IMPORTANT

—

Observeallgoverning

codesandordinances.

•

Note to Installer –

Besuretoleavethese

instructionswiththeconsumer.

•

Note to Consumer –

Keeptheseinstructionsfor

futurereference.

•

Skill level –

Installationofthisappliancerequiresa

qualifiedinstallerorelectrician.

•

Properinstallationistheresponsibilityoftheinstaller.

•

ProductfailureduetoimproperinstallationisNOT

coveredunderthewarranty.

30” Electric

Drop-In Ranges

Installation

Instructions

Questions?

Call800.GE.CARES(800.432.2737)orVisitourWebsiteat:www.GEAppliances.com.

InCanada,call1.800.561.3344orvisitwww.GEAppliances.ca.

•

ATTENTION INSTALLER:

Allelectricdrop-inrangesmustbehardwired(directwired)intoan

approvedjunctionbox.AplugandreceptacleisNOTpermittedontheseproducts.

FOR YOUR SAFETY

WARNING

Beforebeginningtheinstallation,switchpoweroffattheservicepanelandlockthe

servicedisconnectingmeanstopreventpowerfrombeingswitchedonaccidentally.Whentheservice

disconnectingmeanscannotbelocked,securelyfastenaprominentwarningdevice,suchasatag,totheservice

panel.

WARNING

Theinformationinthismanualmustbefollowedtominimizetheriskoffire,electricshock,

ortopreventpropertydamage,personalinjuryorlossoflife.

MATERIALS YOU MAY NEED

JunctionBox
WireNuts
StrainReliefClampfor1/2”Conduit

TOOLS YOU MAY NEED

1/8”DrillBitandElectricDrill

PhillipsScrewdriver

Level

FlatheadScrewdriver

TapeMeasure

1/4”NutDriver

StraightedgeorSquare

Hammer

HandorSaberSaw

Pencil

SafetyGlasses

A child or adult can tip the range and be killed.

Verify the anti-tip bracket has been properly installed

and engaged.

Ensure the anti-tip bracket is re-engaged when the range

is moved.

Do not operate the range without the anti-tip bracket in

place and engaged.

Failure to follow these instructions can result in death or

serious burns to children or adults.

Tip-Over Hazard

WARNING

Oven

Anti-Tip Bracket

Countertop or

Wood Block

Rear

Wall

Summary of Contents for GE Profile JDS28DNWW

























Search results

Summary of Contents for GE Profile JDS28DNWW

Reviews:

Related manuals for GE Profile JDS28DNWW

Brands by name

Popular brands

GE GE Profile JDS28DNWW, Installation Instructions Manual

Search results

Summary of Contents for GE Profile JDS28DNWW

Reviews:

Related manuals for GE Profile JDS28DNWW

Brands by name

Popular brands