![background image](http://html.mh-extra.com/html/ge/ez-light-christmas-trees/ez-light-christmas-trees_user-manual_3049627001.webp)
FOR HINGED TREE
3. Locate and untwist the
red
metal tie wrap holding
the branches in place.
Hint: if your branches do not fall into place, DO NOT
force down. Gently lift up on the branch panels to
release the branch from its locked position.{Fig. D}
Now, all rows of branches should be in the open position.
Before adding the next section, follow the shaping
instructions listed below in Step 1.
Step 1: For a natural uniform look, position some
branches outward and some upward. {Fig. E}
Repeat for each branch panel and each tree section.
The thumbscrew is to be threaded into the stand.
Insert or back-out accordingly. Look for the bottom
section of the tree, identified by a
red-colored
plastic
protective cap at the bottom of the
pole. Remove the cap and place the
pole into the tree stand and tighten
the thumbscrew. { Figs.B and C}
For some 7' to 12’ trees, after removing
the bubble wrap, look for the tag marked "A" attached
to the outer layer of branches. Remove the cap and
place the pole into the tree stand and tighten the
thumbscrew.
Thumbscrew
F
Review Following Terms Carefully
(provided with some trees )
1. Carefully unpack, removing any bubble wrap and inspect the
contents of your tree. {Fig. A}
A
NOTE: Before opening stand make certain thumbscrew is loosened/
removed to not interfere with opening legs.
2. Remove the tree stand from the storage bag and open by pulling
apart two legs on the same side until they are 90 to each other.
NOTE:
No tools required
Tree Sections Tree Stand Approx. Asm Time *
3’ – 4.5’
trees
2
Metal 5 – 10 minutes
5’ – 6.5’
trees
3
Metal
10 – 15 minutes
7’-9’
trees 3 or 4 Metal
10 – 15 minutes
9’– 10.5’
trees 5
Metal
15 – 20 minutes
12’
trees 6, or 7
Metal 25 – 30 minutes
* Does not include time for shaping branches, estimated shaping time is 30 minutes/section;
Recommend use of a stepladder for trees over 6' ; Recommend two people for 12' tree
Outlet
Plug
End Connector
NOTE: due to different metal stand designs, trees are shipped with
the thumbscrew either already threaded into the stand or packaged
separately in a bag. Make certain to check for the thumbscrew
before discarding the storage bag.
Hint: your assembled tree may be heavy and difficult to
move so place the stand in the desired location before
assembling.
The spare 7 amp fuse(s) for the LONG extension cord(s)
at the BOTTOM of your tree are located within the plug
cavity.
Spare Parts: Your Tree includes a plastic bag containing
spare bulbs, replaceable fused bulbs, spare 3-amp fuses,
as replacements for the lighting strings and (1) 5-amp fuse.
NOTE: This 5-amp fuse is ONLY to replace an open
fuse in the SHORT extension cord WITHIN a tree section.
4. If your tree contains only 2 sections, skip to 5.
Locate the middle section, identified by having a green
colored plastic protective cap. Remove the green cap from the
end of the middle section. For some 7' to 12’ trees, look for tags
marked B, then C to F attached to the outer layer of branches.
Starting with “B”, remove the end green cap and proceed.
Disclaimer : DO NOT USE OR INSTALL ANY ADDITIONAL
CHRISTMAS LIGHTING OR ORNAMENTATION THAT IS
POWERED BY A LIGHT BULB SOCKET. DOING THIS MAY
RESULT IN DAMAGE TO YOUR CHRISTMAS TREE OR CAUSE
PERSONAL INJURY. DOING THIS, WILL RESULT IN A VOID OF
THE LIMITED WARRANTY OF THIS PRODUCT.
Distributed by Nicolas Holiday Inc.,
For indoor use only
©
2014 Nicolas Holiday Inc.,
9 F., No. 37, Guangfu North Rd.
Taipei, Taiwan 10560
All rights reserved.
THIS IS NOT A TOY, FOR DECORATIVE USE ONLY.
Printed in China
HG14W
D
E
B
C
F
To electrically connect the sections, fully insert the
plug from the extension cord attached to the pole of
the middle section into the extension cord outlet
attached to the pole near the top of the bottom section.
NOTE: For some 5’- 6.5’ trees fully insert the plug from
the bottom layer of branches from the middle section
into the end connector from the top layer of branches
from the bottom section.
NOTE: For some 6‘-7.5’ trees, the middle section has
one long lead wire. Bring it down the tree and fully
insert the plug into the female end (add-on) of the
plug from the long lead wire from the bottom section
(2 plugs stacked together).
NOTE: For some 9’ to 12’ trees there are two wrapped
extension cords attached to sections marked A and
either B or C.
5.The bottom section of your tree also contains a wrapped
extension cord. Remove the twist tie and straighten
out the cord. At the end of the extension cord is a plug
and on some trees an On/Off FOOT PEDAL. Insert the plug
fully into a working wall outlet. Stepping on the foot
pedal will turn the power to tree On or Off.
NOTE: For trees without an extension cord, remove the
twist tie from the wrapped lead wire at the bottom of the
tree and fully insert the plug into a working wall outlet.
6.Except for some 7’ to 12’ trees, your tree, as
assembled, should now be illuminated. For some
7’ to 12’ trees, continue to add the remaining sections,
connecting the plug on the extension cord at the
bottom of the upper section into the extension cord
outlet near the top of the adjoining lower section.
Hint: If the tree does not illuminate, try stepping on
the foot pedal as the power may be Off. Also, refer
to the Trouble Shooting Tips section.
8. To illuminate the top, fully insert the plug from the top
section into either the end connector or the extension cord
outlet on or near the top layer of branches of previously
assembled pole. Finish Shaping the treetop as necessary
according to the instructions in Step 1. Re-connect power
to the tree. All sections of your tree should now be
illuminated. {Fig. H}
7.Disconnect power to the tree by removing the plug
from the wall outlet. DO NOT remove by pulling on the
cord. The remaining section to assemble is the treetop.
Hint: Shape the top prior to assembly. To shape, gently
press the branches down and away from the center
Insert the top section into the opening at the top of
the last section assembled.(Fig. G) .
G
9. Please check your tree for any loose, unlit or
damaged bulbs. They must be replaced promptly in
order to maintain the performance and life expectancy
of your pre-lit tree.
Your Christmas tree is complete and ready to decorate!
H
NOTE: This stabilizes your tree
keeping the middle section
from turning and properly
aligning the branch
panels.Untwist the
red
metal tie wrap
holding the branches
in place.
Refer to Hint in 3.
Repeat the shaping
instructions in Step 1.
F
Find the locating key inside the bottom opening of the
tree pole from the middle section or the section marked “B”.
Find the groove key located at the top of the tree pole from
the bottom section or the section marked “A”. Align the
locating key and groove and insert the middle section
over the opening in the bottom section, sliding the key down
the groove until fully seated.
NOTE: locate the white vertical line at the top of the metal
pole of the bottom section (or the lower section just
assembled). Locate the white mark on the branch holder
frame on the middle section (or the section being assembled).
Align these two visible white marks to assemble the tree
sections together.{Fig. F} NOTE: For white trees, the color
of the distinguishing marks on the pole and branch
holder will be light green.
NOTE: on some models, the top and bottom sections
are already electrically connected.
Insert the top into the bottom being careful to keep
the cord from entering the opening and damaging
the wires.
Most Frequently Asked Questions
Q. May I add a lighted, decorative tree top to my tree?
A. Yes, There is an outlet on the back of the bladed
plug of the tree top.
Q. May I put blinking or flashing bulbs on my tree?
A. No
Q. May I add extra string sets to my pre-lit tree?
A. No
Q. May I put my pre-lit tree outside?
A. No. Pre-lit trees are for indoor use only.
Q. May I hang glass ornaments on a pre-lit tree?
A. Yes, however, do not hang directly on the wires
of the lights.
Q. May I remove a light string bulb and add a pig
tailed illuminated or animated ornament or motor?
A. No, removing the bulbs and inserting any additional
device into a lamp holder will cause the light set to
cease to operate and may revoke the limited
warranty of this product.
Tree Storage
1. Remove the tree’s main extension cord plug from
the wall outlet. Do not unplug by pulling on the cord.
2. Starting at the top, untwist the securing cap and
disconnect the male and female connectors between
the top and section B.
3. Carefully lift the treetop straight up* from the lower
section. If tightly seated, then wiggle treetop slightly
to loosen.
* Use of a ladder is suggested to avoid bending of
the treetop. Please exercise care when using a
ladder to maintain balance.
Step A: Gently fold the branches up toward the center.
Care should be taken to avoid damage to the lights.
4. Place the treetop into your original shipping carton
with the top in a corner at one end.
5. Untwist the securing cap and disconnect the male
and female connectors between sections B and A.
6. Remove section B, collapse the hinges, repeat
Step A and set-aside.
7. While holding the tree pole of section A, loosen
the thumbscrew located on the tree stand.
8. Remove section A from the tree stand, collapse
the hinges and repeat Step A.
9. Place section A into the carton with the top of the
section at the opposite end of the treetop, as pole
A lays along side the treetop.
10. To close the tree stand for storage, loosen thumbscrew
sufficiently to then push the legs inward.
11. Place the tree stand vertically along the long side
of the carton or lay it flat on the bottom.
12. Carefully place section B into the carton over the
Treetop with its pole lying along side section A.
13. Seal the carton closed.
Important: Store your carton neatly in a cool, dry location
protected from sunlight to prolong the tree life and to
better keep the light
sets in working order.
Do not place a
heavy load on the
carton to avoid
damage to or
crushing the carton
and tree inside.
TOP
A
B
Trouble Shooting Tips
If the tree does not illuminate, try stepping on the
On/Off FOOT PEDAL and make certain the wall switch
is turned on.
If one section of your tree does not illuminate, check
that section for loose or missing bulbs, all factory
connections are properly made or that you properly
made all the electrical connections between each
tree section, i.e., tree plug to extension cord outlet.
Also, check the fused plug for a missing or burned out
(open) fuse.
16.7"X11.2"
General Electric EZ Light
®
Christmas Trees
Assembly Instructions
ATTENTION:
Replaceable fused lamps - identified by the
white colored ring at the top of the lamp holder.
Refer to the UL light string instructions when
replacing these lamps.
Nicolas Holiday Inc. thanks you for your purchase of this pre-lit
Christmas tree. With proper use and care, your Christmas tree will
provide years of use and memories.
Carefully follow the instructions below on how to assemble and
disassemble your pre-lit Christmas tree.
If you should have any problems with your tree, or if the tree does not
light after assembly, DO NOT return it to the place of purchase. Please
refer to the troubleshooting section of this manual or call our toll free
number: 1-877-398-7337 and a customer support representative will
assist you.
Our customer support center is open Monday through Friday 10AM
to 7PM EST with additional hours throughout the holiday season:
November 15th to December 23rd:
Monday-Friday 8AM to 8PM EST,
Saturday-Sunday: 10AM to 7PM EST
You may also visit us on the web at
www.geholidaylighting.com
Enjoy your holiday!
TOP
A
B