OPEN
16.7"X11.2"
Distributed by Nicolas Holiday Inc.,
For indoor use only
©
2017 Nicolas Holiday Inc.,
9 F., No. 37, Guangfu North Rd.
Taipei, Taiwan 10560
All rights reserved.
THIS IS NOT A TOY, FOR DECORATIVE USE ONLY.
Printed in China
HG17-LED-ONEPLUG
Tree Storage
1.
Remove the tree’s main plug from the wall outlet.
2.
Starting at the top, disconnect the top and section
B (or C).
Step A:
Gently fold the branches up toward the center.
Care Should be taken to avoid damage to the lights.
3.
Disconnect sections B and A (or sections C and B).
4.
Refer to the drawing on how to repack your tree.
Important: Store your carton neatly in a cool, dry location
protected from sunlight to prolong the tree life and to
better keep the light sets in working order. Do not place a
heavy load on the carton to avoid damage to or crushing
the carton and tree inside.
tree
top
tree stand
A B C
(FOR 9 FT
TREES)
Remove and unwrap all parts.
Retain shipping carton for repacking.
1
For proper installation and use, the
tree must be set up in a clear area
without any obstructions and on a
flat surface.
NOTE:
Before opening stand, be certain the
thumbscrew is loosened, so it does not
interfere with opening legs.
Place stand in desired location before
assembling. Your assembled tree will
be heavy and
difficult to move.
Open tree stand.
2
Tighten screw to
secure section A
in the tree stand.
NOTE:
Remove twist tie around looped
wires with plug adapter, extend wire and
set aside.
Untie RED twist-tie to release
branch panels.
Hint:
if your
branches do not fall
into place, DO NOT
force down. Gently
lift up on the branch
panels to release the
branch from its locked position. Now, all
rows of branches should be in the open
position.
Before adding the next section, follow the
shaping instructions listed below in
NOTE
.
NOTE:
For a natural uniform look, position
some branches
outward and
some upward.
Repeat for each
branch panel
and each
tree section.
3
Assemble section B into section A.
Firmly seat both sections together.
4
Assemble section C
into section B.
Firmly seat both
sections together.
5
Hold tree top with one
hand as shown. Gently
pull down the outer
layer of branches, and
fully insert tree top
into the top of the
pole on section
B. (or C)
6
To illuminate your tree, insert
plug directly into an
electrical wall outlet.
If needed, adjust
branch tips to make
the tree look fuller.
Congratulations!
Your tree is complete
and ready to
decorate.
7
Insert section A into tree stand, after
first removing red protective cap.
Repeat step 3.
Repeat step 3.
Most Frequently Asked Questions
Q. May I add a lighted, decorative tree top to my tree?
A. Yes, But you would have to use separate extension
cord to power the tree topper.
Q. May I put blinking or flashing bulbs on my tree?
A. No
Q. May I add extra string sets to my pre-lit tree?
A. No
Q. May I put my pre-lit tree outside?
A. No. Pre-lit trees are for indoor use only.
Q. May I hang glass ornaments on a pre-lit tree?
A. Yes, however, do not hang directly on the wires
of the lights.
Q. May I remove a light string bulb and add a pig
tailed illuminated or animated ornament or motor?
A. No, removing the bulbs and inserting any additional
device into a lamp holder will cause the light set to
cease to operate and may revoke the limited
warranty of this product.
Disclaimer : DO NOT USE OR INSTALL ANY ADDITIONAL
CHRISTMAS LIGHTING OR ORNAMENTATION THAT IS
POWERED BY A LIGHT BULB SOCKET. DOING THIS MAY
RESULT IN DAMAGE TO YOUR CHRISTMAS TREE OR CAUSE
PERSONAL INJURY. DOING THIS, WILL RESULT IN A VOID OF
THE LIMITED WARRANTY OF THIS PRODUCT.
GE Branded Christmas Trees
Easy Light Technology
®
eliminates cord connections
Just assemble and decorate!
GE is a trademark of General Electric Company
and is under license by Nicolas Holiday Inc.
Spare Parts: Your tree includes a plastic bag containing
spare LEDs.
Troubleshooting Tips
If one section of your tree does not illuminate, check
that section for loose or missing bulbs, all factory
connections are properly made or that you properly
made all the electrical connections between each
tree section, i.e., tree plug to extension cord outlet.
Also, check the fused plug for a missing or burned out
(open) fuse.
9 FT TREES
B
A
TOP
B
C
A
TOP
7.5 FT TREES
TOP
B
A
TREE ASSEMBLY DIAGRAM
C
TREE
STAND
9 FT
7 FT & 7.5 FT
TOP
B
A
TREE
STAND
Note:
Always unplug this product before installing.
Do not plug in, until entire tree assembled.
Nicolas Holiday Inc. thanks you for your purchase of this pre-lit
Christmas tree. With proper use and care, your Christmas tree
will provide years of use and memories.
Carefully follow the instructions below on how to assemble and
disassemble your pre-lit Christmas tree.
If you should have any problems with your tree, or if the tree
does not light after assembly, DO NOT return it to the place of
purchase. Please refer to the troubleshooting section of this
manual or call our toll free number: 1-877-398-7337 and a
customer support representative will assist you.
Our customer support center is open Monday through
Friday 10AM to 7PM EST with additional hours throughout
the holiday season:
Nov 11 to Dec 23:
Monday – Friday 8:00 am to 8:00 pm EST,
Saturday – Sunday 10:00 am to 7:00 pm EST
*Note: Schedule is subject to change at any time. Please check
back before contacting us for the most up-to-date schedule.
You may also visit us on the web at
www.geholidaylighting.com
Enjoy your holiday!
