![background image](http://html1.mh-extra.com/html/gb/ssba18n-s/ssba18n-s_supplemental-instructions_570656001.webp)
SUPPLEMENTAL INSTRUCTIONS
GB “Space Saving “ Burner Assembly
Model Numbers
SSBA18N-S
SSBA24N-S
SSBA18L-S
SSBA24L-S
SSBA30N-S
SSBA30L-S
Model Numbers
A-SSBA18NS
A-SSBA24NS
A-SSBA18LS
A-SSBA24LS
A-SSBA30NS
A-SSBA30LS
Component Parts
1. Gas Burner Pan
2. 3 in 1 Gas Valve
3. Thermocouple Assembly
4. Nat. Gas Orifice (Lp Air Mixer, Lp Gas Model)
5. Control Knob
6. Pilot Flame Adjustment
7. Gas Connection Fitting
CSA Models also have installed Gas Regulator
between Gas Connection Fitting and Valve
FOR YOUR SAFETY READ BEFORE LIGHTING
WARNING: IF YOU DO NOT FOLLOW THESE INSTRUCTIONS EXACTLY, A FIRE OR
EXPLOSION MAY RESULT CAUSING PROPERTY DAMAGE, PERSONAL INJURY OR LOSS OF
LIFE.
1. This product has a standing pilot, which must be lit by hand. When lighting the pilot, follow these
instructions exactly.
2. This installation should be installed including provisions for combustion and ventilation air, must
conform with local codes or, in the absence of local codes, to the National Fuel Gas Code, Ansi
Z223 latest edition.
3. This product must be on gas supply line that is less than 1/2 psi. and with an individual manual
shut off.
4.
Never
operate this new system with the glass fireplace enclosures (doors) in the closed position.
5. Connecting 110-volt electrical power to this product will cause damage and will void warranty.
After completion of “To Install Gas Log Set”
Instructions in installation instructions, position
grate over Burner Assembly as shown in
(figure 2)
( Figure 1 )
2
1
3
4
5
6
7
( Figure 2 )
OPERATING INSTRUCTIONS
Pilot Gas and Lighting Procedure
5.
Turn the gas control knob counter clockwise to the pilot position, push the gas control knob In and Hold in
position. This will open the pilot valve and allows gas to flow to the pilot burner.
6.
Light the pilot burner while holding the gas control knob in until a strong pilot flame is present. (Approximately 60
seconds)
7.
Release the gas control knob. The gas control knob will hold in and engages the valve power unit.
8.
Turn the gas control knob counter clockwise to the On position, The main burner valve will open and the
main burner will ignite.
SHUT OFF PROCEDURE
1.
To shut off the main burner but leaving the pilot on, turn the gas control knob clockwise to the pilot position.
This action will close the main gas flow.
2.
To shut off the main burner and pilot, turn the gas control knob clockwise to the off position. This action will
close the main gas valve and disengages the safety pilot valve. However the power unit must drop out before the
lighting sequence can begin again. This may take as long as 3 minutes.
3.
To relight the pilot, follow the steps in the Pilot Gas and Lighting Procedure section.
HEAT SHIELD INSTALLATION
Position Heat Shield over valve as shown in Figure 3
(Bottom of Shield is notched to allow shield to be
placed over valve bracket to insure proper position)
OPTIONAL LIGHTING METHODS
All GB 3 in 1 Valves can be converted from a
manual valve to a remote On/Off latching solenoid
valve or a Remote Variable On/Off High/Low motor-
ized valve by adding optional solenoid or motor to
this valve. (Figure 4)
Ask your dealer for details or call 1-800-833-1139
$
$
$
$
( Figure 3 )
( Figure 4 )
Location for
attaching
optional
lighting
component