Gasmate Blaze Installation, Operation And Maintenance Instructions Download

Page: 1 / 12

Blaze Outdoor Heater

Model No. GM124-028

FOR YOUR SAFETY

If you smell gas:

1. Shut off the gas to the

appliance.

2. Extinguish any open flame.

3. If odour continues,

immediately call your gas
supplier.

Do not store or use gasoline
or other flammable vapour and
liquids in the vicinity of this or any
other appliance.

WARNING:

Improper installation, adjustment,
alteration, service or maintenance
can cause injury or property
damage.

Read the instructions thoroughly
before installing or servicing this
equipment.

Important: The installer or seller must leave these instructions with the consumer.

IMPORTANT:

•

Retain these instructions for future use.

4782-07/17

FOR OUTDOOR USE

ONLY

OPERATES ON

LPG/ULPG

•  The glass tube will be extremely
  hot when it is working so never
  try to touch it and keep children
away.

• Turn off the appliance

immediately if it starts raining
and never use it while it is

  raining as the glass tube may
  break when it comes in contact
  with water.

• Never splash any liquid onto

the glass tube when the

appliance is on.

• Always ensure the appliance

  stands on a flat, firm surface as
  the glass tube may break if the
  appliance falls over.

• Never use the appliance if the
glass tube has any cracks or

damage.

Summary of Contents for Blaze













Search results

Summary of Contents for Blaze

Reviews:

Related manuals for Blaze

Brands by name

Popular brands

Gasmate Blaze, Installation, Operation And Maintenance Instructions

Search results

Summary of Contents for Blaze

Reviews:

Related manuals for Blaze

Brands by name

Popular brands