Galaxy Audio RM-RDSTNR, Quick Start Manual

Page: 1 / 2

Included Components
1.
AM/FM RDS Tuner x1
3. FM Antenna Wire x1
4. Dual RCA Cable x1
5.
AC Power Cord x1
6.
Remote Control x1
7.
Quick Start Guide x1
1.
2.
7.
2.
AM Antenna Set x1
1.
Rack Screws 10/32 x .75",
Phillips Truss Head Screws
2.
#2 Phillips Head Screwdriver
1.
2.
What May be Needed to Rack
(Not Included)
Racking/Mounting
(Optional)
Setup
Operation
6.
3.
4.
5.
1
Connect Power Cable to the
RM-RDSTNR. Connect the other end to
a power outlet. (Optional DC 13.2 Power
Cable may also be used)
2
Attach the AM and/or FM Antenna on
the RM-RDSTNR.
3
Make sure the volume is reduced until
ready for sound. Connect RCA Cable to
the Left and Right RCA Outputs and
connect to Amplifier, Mixer, or Receiver.
4
Power on the RM-RDSTNR Tuner.
1
To Select FM 1, FM 2 or AM frequencies,
Press “BAND”.
3
To start auto scan search, hold TUNING
for over 2 seconds.
4
6 7 8 9
To use Sleep function, press “SLEEP”
on the Remote. (Every press adds
10 min, with 90 min being max.)
5
Align RDS Tuner up evenly. Turn the
screw but leave room to adjust. Once
all four screws are in place, tighten
securely.
5
10
To cancel Sleep, press “SLEEP” until
the LCD shows “00”.
2
Press “TUNING ” or “TUNING ”
to select channel.
GAL A X Y AUDIO
Quick Start Guide
RM-RDSTNR
AM / FM RDS Tuner
OR
OR OR
To set a memory CH, press “MEMORY”
then press “1~5”, then Memory again.
(10 memory assignable per freq. band)
To choose Mono or Stereo mode, Press
“MO / ST”.
To set above 5, press , then Memory
“+5”, then “1~5” and press Memory
again. Ex: “+5” and “3” to set it at CH8.
To listen to a saved CH, press
“MEMORY UP” or “M1~M5”. To select
higher, use “+5” and “M1~M5”.
Ex: “+5” and “M3” = CH8. To search and go to a travel/traffic
station (if available in area), press TA.
Included Components
1. AM/FM RDS Tuner x1
3. FM Antenna Wire x1
4. Dual RCA Cable x1
5. AC Power Cord x1
6. Remote Control x1
7. Quick Start Guide x1
1.
2.
6.
5.
2. AM Antenna Set x1 1. Rack Screws 10/32 x .75",
Phillips Truss Head Screws
2. #2 Phillips Head Screwdriver
1.
2.
What May be Needed to Rack
(Not Included)
Racking/Mounting (Optional) Setup
Operation
3.
4.
1
Connect Power Cable to the
RM-RDSTNR. Connect the other end to
a power outlet. (Optional DC 13.2 Power
Cable may also be used)
2
Attach the AM and/or FM Antenna on
the RM-RDSTNR.
3 4
Power on the RM-RDSTNR Tuner.
1
To Select FM 1, FM 2 or AM frequencies,
Press “BAND”.
3
To start auto scan search, hold TUNING
for over 2 seconds.
9
To use Sleep function, press “SLEEP”
on the Remote. (Every press adds
10 min, with 90 min being max.)
5
Align RDS Tuner up evenly. Turn the
screw but leave room to adjust. Once
all four screws are in place, tighten
securely.
10
To cancel Sleep, press “SLEEP” until
the LCD shows “00”.
2
Press “TUNING ” or “TUNING ”
to select channel.
GAL A X Y AUDIO
Quick Start Guide
RM-RDSTNR AM / FM RDS Tuner
OR
OR OR
7.
3
Make sure the volume is reduced until
ready for sound. Connect RCA Cable to
the Left and Right RCA Outputs and
connect to Amplifier, Mixer, or Receiver.
4
6 7 8
5
GAL A X Y AUDIO
Quick Start Guide
RM-RDSTNR AM / FM RDS Tuner
To set a memory CH, press “MEMORY”
then press “1~5”, then Memory again.
(10 memory assignable per freq. band)
hoos Mono or Stereo mode To c e , Press
“MO / ST”.
To set above 5, press , then Memory
“+5”, then “1~5” and press Memory
again. Ex: “+5” and “3” to set it at CH8.
To listen to a saved CH, press
“MEMORY UP” or “M1~M5”. To select
higher, use “+5” and “M1~M5”.
Ex: “+5” and “M3” = CH8. To search and go to a travel/traffic
station (if available in area), press TA.