Fujitsu DL7400 Installation Manual Download

Page: 1 / 46

Installation guide for Fujitsu Dot Matrix Printer_1.6

Page 1

Installation Guide for Fujitsu Dot Matrix Printer 1.6

Version History:

VERSION

DESCRIPTION

AUTHOR

DATE

0.1

Draft written for first initial review

Henry Chan

20Oct2011

0.2

Update the prerequisites section & minor
changes

Henry Chan

21Oct2011

1.0

Added additional prerequisites

Henry Chan

4Nov2011

1.2

- Updated the prerequisites for user &
engineer.
- 2 generic local administrator account &
password for CX owned PC

Prashant Pande

30Nov2011

1.3

Incorporate documentation for IE8 settings
required for ezyfreight Print MAWB
function

Pak Wong

03Jan2012

1.4

Updated the installation pre-requisites for
IE requirements.

Pak Wong

11Jan2012

1.5

Updated the installation pre-requisites for
CX PC Asset Ids.

Pak Wong

18Jan2012

1.6

Updated the skipping of IE security setting
for CX computers

Henry Chan

14Feb2012

About this manual:

This installation guide is designed for onsite Fujitsu engineer to:

Unpack and setup the dot matrix printer;

Install the printer drivers; and

Be able to print the AWB print form via the Ezyfreight web application.

Fujitsu DL7400 Dot Matrix Printer will be used as an example in this manual.

Please read this Installation Guide thoroughly before going onsite to

perform the installation. If you have any questions regarding the

installation procedure please contact Fujitsu Hong Kong

(<[email protected]>).

Summary of Contents for DL7400















































Search results

Summary of Contents for DL7400

Reviews:

Related manuals for DL7400

Brands by name

Popular brands

Fujitsu DL7400, Installation Manual

Search results

Summary of Contents for DL7400

Reviews:

Related manuals for DL7400

Brands by name

Popular brands