background image

TO BE REMOVED BY THE CUSTOMER AFTER INSTALLATION IS COMPLETE

INSTALLATION CHECKOFF LIST

Doors

Handles are secure and tight
Door seals completely to cabinet on all sides
Freezer door is level across the top

Leveling

Refrigerator is level, side to side and tilted 1/4” (6mm) front to back
Toe grille is properly attached to refrigerator
Cabinet is setting solid on all corners

Electrical Power

House power turned on
Refrigerator plugged in

Ice Maker

House water supply connected to refrigerator
No water leaks present at all connections - recheck in 24 hours
Ice Maker is turned ON.

Final Checks

Shipping material removed
Fresh Food and Freezer controls set
Crisper Humidity controls set
Registration Card sent in

Refer to your 

Owner’s Use and Care Manual for

additional information about your refrigerator.

• Load refrigerator from side of cabinet only.
• Do not run retaining straps over handles.
• Do not over-tighten retaining straps.
• Never use refrigerator handles to move the

refrigerator.

• Remove tape from doors only after unit is in

place.

HAND TRUCKING

1

Remove Shipping material. (Features may vary per model.)

2

SHIPPING MATERIAL

3

Connect water supply - check for water
leaks. 

Turn icemaker OFF if water supply

is not connected immediately.
Connecting to a reverse osmosis system
is not recommended.

WATER SUPPLY

eçìëÉ

éäìãÄáåÖ

äáåÉ

t~íÉêäáåÉ=Üççâìé

WATER SUPPLY

_É=ÅÉêí~áå

íÜÉ=ï~íÉê=î~äîÉ=áë

çéÉå=~åÇ=íÜÉêÉ

~êÉ=åç=äÉ~âëK

qÜÉ=ï~íÉê=î~äîÉ

çå=íÜÉ=Ä~Åâ=çÑ

íÜÉ=êÉÑêáÖÉê~íçê

ïáää=`äáÅâL_ìòò=áÑ

íÜÉ=ï~íÉê=î~äîÉ

áë=ÅäçëÉÇK

4

Allow the following clearances for ease of installation, proper air circulation, and
plumbing and electrical connections:

Sides & Top..........3/8”

Back.......................1”

INSTALLATION CLEARANCES

NO

NO

NO

NO

NOTE

TE

TE

TE

TE

If you are installing your refrigerator beside a wall, leave 1/2” minimum between

hinges and wall to allow for the door to swing open.

5

All four corners of your refrigerator must rest firmly on a solid floor. Your refrigerator
is equipped with adjustable front rollers or front leveling screws to help level your
unit.

To level cabinet or change door height:

1. Remove toe grille.
2.

Use flat-blade screwdriver or 3/8” socket wrench to adjust front rollers. Use
adjustable wrench to adjust leveling screws.

LEVELING AND ADJUSTING

NO

NO

NO

NO

NOTE

TE

TE

TE

TE

Raise the front of the refrigerator enough so the doors close freely when opened
halfway. The refrigerator should slope ¼” to ½” from front to back. Then level the

refrigerator from side to side.

6

Toe Grille

Adjustable Front Roller

(some models)

Raise

Stationary Front Roller

with Leveling Screw

(some models)

When changing controls, wait 24
hours before making additional
adjustments.

CONTROLS

7

Ensure icemaker
is turned ON.

8

ICEMAKER

DOOR

REMOVAL

(IF NECESSARY)

IF YOU ARE DISSATISFIED WITH THE

INSTALLATION, PLEASE CALL THE STORE

YOU PURCHASED IT FROM.

9

See “Normal Operating Sights & Sounds”

 in the 

Use & Care Manual

so you understand the sounds you may hear once your refrigerator is
running.

Please read entire 

Use & Care Manual 

to become aware of important

safety instructions and to become familiar witrh your new refrigerator.

Send in Registration card

 to register your refrigerator.

Congratulations! 

You are ready to enjoy your new refrigerator.

P/N: 240568303

Humidity

Control

Center

Hinge

Shim

Pin

Top Hinge
Cover

Top Hinge

If you need to remove the doors to get your refrigerator
into the house please see “Door Removal and Reversal
Instructions” in your 

Use & Care Manual.

Bottom

Water Tube

Cable

Wood

Top Hinge
Cover

Top Hinge

OR

Отзывы: