Frigidaire GLMV168C Installation Instructions Manual Download

Page: 1 / 24

READ CAREFULLY.

KEEP THESE INSTRUCTIONS

Installation

Over the Range

Instructions

Microwave Oven

Read these instructions completely and carefully.

•

IMPORTANT –

Save these

instructions for local inspector’s use.

•

IMPORTANT –

Observe all

governing codes and ordinances.

•

Note to Installer –

Be sure to leave these

instructions with the Consumer.

BEFORE YOU BEGIN

•

Note to Consumer –

Keep these

instructions for future reference.

•

Skill level

– Installation of this appliance requires

basic mechanical and electrical skills.

•

Proper installation is the responsibility of the installer.

•

Product failure due to improper installation is not
covered under the Warranty.

Need Help?
For customers in the United States, call: 1-800-944-9044
For Canadian customers, call: 1-866-294-9911

P/N 316137222

Summary of Contents for GLMV168C

























Search results

Summary of Contents for GLMV168C

Reviews:

Related manuals for GLMV168C

Brands by name

Popular brands

Frigidaire GLMV168C, Installation Instructions Manual

Search results

Summary of Contents for GLMV168C

Reviews:

Related manuals for GLMV168C

Brands by name

Popular brands