background image

NOTICE

 - 

This service data sheet is intended for use by persons having electrical and mechanical training and a level of knowledge of these subjects

generally considered acceptable in the appliance repair trade.  The manufacturer cannot be responsible, nor assume any liability for injury or damage
of any kind arising from the use of this data sheet.

SAFE SERVICING PRACTICES

To avoid the possibility of personal injury and/or property damage, it is important that safe servicing practices be observed.  The following are examples, but without
limitation, of such practices.

1.

Before servicing or moving an appliance remove power cord from electrical outlet, trip circuit breaker to OFF, or remove fuse.

2.

Never interfere with the proper installation of any safety device.

3.

GROUNDING:  The standard color coding for safety ground wires is GREEN or GREEN WITH YELLOW STRIPES.  Ground leads are not to be used as current
carrying conductors.  It is extremely important that the service technician reestablish all safety grounds prior to completion of service.  Failure to
do so will create a potential safety hazard.

4.

Prior to returning the product to service, ensure that:
• All electric connections are correct and secure.
• All electrical leads are properly dressed and secured away from sharp edges, high-temperature components, and moving parts.
• All uninsulated electrical terminals, connectors, heaters, etc. are adequately spaced away from all metal parts and panels.
• All safety grounds (both internal and external) are correctly and securely reassembled.

SPEED BAKE MODE (some models)

The Speed Bake mode uses the addition of a fan to move the heated air already in the oven.  Moving the heated air helps to destratify the heat and cause uniform
heat distribution.  Cooking times can be reduced by as much as 30%.  The air is drawn in through a fan shroud located in the rear wall of the oven.  It is then discharged
around the outer edges of this shroud.  The air circulates around the food and then enters the shroud again.  As with conventional gas ranges, there is still an oven
vent which discharges behind the top cooking surface.

To set the oven to Speed Bake mode, follow these steps:
1.

Program the oven as you normally would for baking.

2.

Push and release the Speed Bake momentary rocker switch.  The indicator light will glow, signifying that the Speed Bake mode has been activated.  The fan
will not come on for the first six minutes, unless the center of the oven temperature is above 350°F when the Speed Bake mode is activated. 
This
is to allow for clean combustion in the gas oven. Six minutes after the Speed Bake mode is activated, the fan will come on. The fan stays on when the oven
door is closed and shuts off while the oven door is opened.  The fan will continue to operate until baking is complete.

3.

To cancel the Speed Bake function, push CANCEL or CLEAR on the oven control as you would to cancel any baking function.

NOTE:  The Speed Bake mode will not work during a clean or broil cycle.

FAN  MOTOR (Speed Bake models only)

The fan motor is mounted on the main back on the back side of the range.  It can be accessed by removing the rear wire shields.

FAN BLADE (Speed Bake models only)

The fan blade is  mounted in the rear of the unit and has a "D" shaped mounting hole.  Only minimum clearance exists between the oven back, fan blade, and fan
shroud.  Be careful not to bend the blade when removing or installing.

Access to the fan blade is gained by removing the fan shroud located inside the oven and held in place by two screws.
The fan blade is held in place with a 13 mm hex nut that has left handed threads.  When removing this nut, gently hold the fan blade, and turn the nut clockwise.

The fan motor runs continuously (after the first six minutes, as defined above)while in Speed Bake
mode unless the door is opened.  If the fan does not operate, check the following:
• Is the oven control in Bake mode?
• Is the Speed Bake indicator light glowing?
• Are 120 volts available at the fan motor?
• Is the fan motor coil resistance 35 ohms ±10%?
• Is the door/light switch working properly?

MOTOR MOUNTING BRACKET (Speed Bake models only)

The fan motor on the rear of the range is mounted through the main back to a mounting bracket
that is attached with three screws to the backside of the rear oven wall.  Should it become necessary
to replace this bracket, the main back must be removed to access the mounting screws.

OVEN CALIBRATION

Set the electronic oven control for normal baking at 350°F.  Obtain an average oven temperature after a minimum of 5 cycles.  Press CANCEL or CLEAR to end
bake mode.

TEMPERATURE ADJUSTMENT

1.

Set EOC to bake at 550°F.

2.

Within 5 seconds of setting 550°F, press and hold the bake pad for approximately 15 seconds until a single beep is heard (longer may cause F1 shorted keypad
alarm).

3.

Calibration offset should appear in the display.

4.

Use the slew keys to adjust the oven temperature up or down 35°F in 5°F increments.

5.

Once the desired (-35° to 35°) offset has been applied, press CANCEL or CLEAR.

Note: Changing calibration affects both Speed Bake and normal bake modes.  The adjustments made will not change the self-cleaning temperature.

P/N  316218504 (0301)

SERVICE DATA SHEET

Gas Ranges with Electronic Oven Control and Speed Bake™ (some models)Cooking System

RESISTANCE

TEMPERATURE

DETECTOR

RTD SCALE

Temperature (°F)

Resistance (ohms)

32 ± 1.9

1000 ± 4.0

75 ± 2.5

1091 ± 5.3

250 ± 4.4

1453 ± 8.9

350 ± 5.4

1654 ± 10.8

450 ± 6.9

1852 ± 13.5

550 ± 8.2

2047 ± 15.8

650 ± 9.6

2237 ± 18.5

900 ± 13.6

2697 ± 24.4

 

 Electrical Shock Hazard can

occur and result in serious injury or death.
Disconnect appliance from electric power before
cleaning and servicing the warmer drawer.

To Remove Warmer Drawer:

1.

 Turn power off before removing the warmer

drawer.

2.

Open the drawer to the fully opened position.

3.

Locate glide lever on each side of drawer, pull up on the left glide
lever and push down on the right glide lever (see Figure 1).

4.

Pull the drawer away from the range.

To Replace Warmer Drawer:
1.

Pull the bearing glides to the front of the chassis glide
(see Figure 2).

2.

Align the glide on each side of the drawer with the glide slots on the
range.

3.

Push the drawer into the range until levers “click” (approximately
2”).  Pull the drawer open again to seat bearing glides into position.
If you do not hear the levers “click” or the bearing glides do
not feel seated remove the drawer and repeat steps 1 thru 3.
This will minimize possible damage to the bearing glides.

Figure 1

Figure 2

REMOVING AND REPLACING WARMER DRAWER (some models)

ELECTRONIC OVEN CONTROL FAULT CODE DESCRIPTIONS

Note: Only three fault codes are displayed by this control - F1F3 or F9. Generally, F1 display implies the electronic oven  control itself has detected an internal
malfunction.  F3 implies the control has detected a sensor probe failure and F9 implies the control has detected a latch motor assembly problem. In any of these
cases, an alarm will accompany a displayed F1F3 or F9.

1.

Shorted keypad.

2.

Control's internal checksum may have become corrupted.

3.

Control has sensed a potential runaway oven condition. Control may
have shorted relay, RTD sensor probe may have gone bad.

1.

Open RTD sensor probe. Note: The EOC will initially display an F1 for
this condition. The EOC thinks a runaway oven condition exists.

2.

Shorted RTD sensor probe. Note: The F3 for shorted probe should only
occur when the oven is active or when an attempt is made to enter a
mode.

Control has detected a problem with the Motor Door Latch Assembly.

Likely Failure Condition/Cause

Suggested Corrective Action

     Fault  Code

1.

Replace EOC.

2.

Disconnect power, wait 30 seconds and reapply power. If fault returns upon
power-up, replace EOC.

3.

Check RTD sensor probe and replace if  necessary. If oven is overheating,
disconnect power. If oven continues to overheat when the power is reapplied,
replace EOC. Severe overheating may require the entire oven to be replaced,
should damage be extensive.

1.

Check resistance at room temperature and compare to RTD sensor resistance
chart. If resistance does not match the chart, replace RTD sensor probe.

2.

Check resistance at room temperature, if less than 500 ohms, replace RTD
sensor probe.

Check the wiring. Replace the Motor Door Latch Assembly if necessary.

F3

F1

F9

ELECTRONIC OVEN CONTROL (REAR VIEW)

If one of the blades becomes deformed, it may be bent back into shape using a flat surface as a
reference. A flat washer is located on the motor shaft between the snap ring on the shaft and the
fan blade.
Note:  If the fan blade is bent and the motor vibrations increase, the noise made by the fan will be
greater.

FAN OPERATION (Speed Bake models only)

IMPORTANT

DO NOT REMOVE THIS BAG

OR DESTROY THE CONTENTS

WIRING DIAGRAMS AND SERVICE

INFORMATION  ENCLOSED

REPLACE CONTENTS IN BAG

Reviews: