background image

 

 

FS-10 

 

REMOTE CONTROL ALARM SYSTEM 

INSTALLATION & OPERATING INSTRUCTIONS 

 

 

INTRODUCTION 

 

CONGRATULATIONS

  on  your  choice  of  a  “

Fortress

”  Remote  Alarm  System  by  Crimestopper  Security 

Products Inc.  This booklet contains the information necessary for installing, using, and maintaining your alarm 
system.  If any questions arise, contact your installation dealer or Crimestopper Security Products Inc. at the 
Tech Support number below. 

 

 

This installation book is designed for the installer or individual with an existing understanding of automotive 
electrical systems, along with the ability to test and connect wires for proper operation.  To ease installation, 
we  suggest  that  you  READ  THIS  MANUAL  before  beginning  your  installation.    This  book  is  provided  as  a 
GENERAL GUIDLINE and the information contained herein may differ from your vehicle. 
 

 

 
         TECH SUPPORT 

Mon-Fri 8:00 AM-4:30 PM Pacific Time 

 

www.crimestopper.com 

 

Phone (800) 998-6880 

 

FAX (805) 581-9500 

 

REV. A  08.2008 
 

 

This  device  complies  with  FCC  Rules  part  15.  Operation  is  subject  to 
the following two conditions: 1) This device may not cause interference, 
and (2) this device must accept any interference that may be received, 
including  interference  that  may  cause  undesired  operation.    The 
manufacturer is not responsible for any radio or TV interference caused 
by  unauthorized  modification  to  this  equipment.  Such  modification 
could void the user's authority to operate the equipment.

 

 

Summary of Contents for CRIMESTOPPER FS-10

















Reviews: