background image

The TrimLine 10' x 20' Canopy

Parts List

This page contains a list of all the parts you should receive for your TrimLine Canopy. Parts for optional 
components are listed with separate instructions for those options. Please review all parts to be sure you 
have everything you need. Should you 

fi

nd anything missing, please call us immediately at: 1-800-296-0049

Page 1

(1) Topper (Roof)

Plastic Ra

ft

er Poles

(14)

 Ra

ft

er End sections - with metal connector on one end

(7)

 Ra

ft

er Center sections

(6) Sidewalls  10 

ft

 wide x 7 

ft

 high

Joints

(4)

 Tie-down Screws

(8)

 10” Steel Spikes

(14) 

Ball Bungees for bundling poles

(26)

 Thumbscrews (includes 1 spare)

Hardware

(2)

 Corner Joints  ATL4 L

      Le

ft

 Side Ra

ft

er Base

(2)

 Corner Joints ATL4 R

      Right Side Ra

ft

er Base

(2)

 4-Way Ra

ft

er Bases

      ATL5

(8)

 Ra

ft

er Bases

      ATT

(2) 

Ridge Pole Supports

TLR

(1)

 2-Way Ridge Support

      TLR2

(3)

 Tee Joints

TL202

(6)

 Feet

      AT211

(2)

 StaBar 3-Ways

      AT200

(2)

 StaBar Ells

      AT202

(1)

 StaBar Tee

     AT210

(over, please)

Summary of Contents for TrimLine 10' x 20'













Reviews: