Model CO910
M08-0477-001 K1
01/14 Printed in Mexico
IMPORTANT! PLEASE READ CAREFULLY AND SAVE.
This user’s manual contains important information about your
Carbon Monoxide Alarm’s operation.
If you are installing this Alarm for use by others, you must leave
this manual—or a copy of it—with the end user.
TABLE OF CONTENTS
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1
Basic Safety Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-3
Where to Install This Alarm . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1
Where This Alarm Should NOT Be Installed . . . . . . . . . . . . . . . . . .2
How to Install This Alarm . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-3
Weekly Testing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
Regular Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
If Your CO Alarm Sounds . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
If the CO Alarm Sounds . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
Using the Silence Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
What You Need To Know About CO . . . . . . . . . . . . . . . . . . . . . . . . . . .4
What is CO? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
Symptoms of CO Poisoning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
Potential Sources of CO in the Home . . . . . . . . . . . . . . . . . . . . . .4
How Can I Protect My Family From CO Poisoning? . . . . . . . . . . . . . .4
Regulatory Information For CO Alarms . . . . . . . . . . . . . . . . . . . . . . . .5
General Limitations Of CO Alarms . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
Troubleshooting Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-6
Limited Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-6
© 2014 BRK Brands, Inc. All rights reserved. Distributed by
BRK Brands, Inc., 3901 Liberty Street Road, Aurora, IL 60504-8122
Consumer Affairs: (800) 323-9005 • www.firstalert.com
INTRODUCTION
BASIC SAFETY INFORMATION
• Dangers, Warnings, and Cautions alert you to important
operating instructions or to potentially hazardous situations.
Pay special attention to these items.
• This CO Alarm is approved for use in single-family
residences. It is NOT designed for marine or RV use.
• This carbon monoxide Alarm is designed to detect carbon
monoxide gas from ANY source of combustion. This CO Alarm
is not designed to detect smoke, fire, or any other gas. It will
only indicate the presence of carbon monoxide gas at the
sensor. Carbon monoxide gas may be present in other areas.
• This unit will not operate without battery power. The CO
Alarm cannot work until you activate the battery power pack.
• NEVER ignore any alarm. See “If Your CO Alarm Sounds” for
more information on how to respond to an alarm. Failure to
respond can result in injury or death.
• The Silence Features are for your convenience only and will
not correct a problem. See "Using the Silence Features" for
details. Always check your home for a potential problem
after any alarm. Failure to do so can result in injury or death.
• Test this CO Alarm once a week. If the Alarm ever fails to
test correctly, have it replaced immediately! If the Alarm is
not working properly, it cannot alert you to a problem.
• This product is intended for use in ordinary indoor locations
of family living units. It is not designed to measure CO levels
in compliance with Occupational Safety and Health
Administration (OSHA) commercial or industrial standards.
Individuals with medical conditions that may make them
more sensitive to carbon monoxide may consider using
warning devices which provide audible and visual signals for
carbon monoxide concentrations under 30 ppm. For addi-
tional information on carbon monoxide and your medical
condition contact your physician.
5
6
1
2
3
CARBON MONOXIDE ALARM
4
FINDING THE SOURCE OF CO AFTER AN ALARM
Carbon monoxide is an odorless, invisible gas, which often makes it
difficult to locate the source of CO after an alarm. These are a few of
the factors that can make it difficult to locate sources of CO:
• House well ventilated before the investigator arrives.
• Problem caused by “backdrafting.”
• Transient CO problem caused by special circumstances.
Because CO may dissipate by the time an investigator arrives, it may
be difficult to locate the source of CO. BRK Brands, Inc. shall not be
obligated to pay for any carbon monoxide investigation or service
call.
POTENTIAL SOURCES OF CO IN THE HOME
Fuel-burning appliances like:
portable heater, gas or wood burning
fireplace, gas kitchen range or cook-
top, gas clothes dryer.
Damaged or insufficient venting:
corroded or disconnected water heater
vent pipe, leaking chimney pipe or flue,
or cracked heat exchanger, blocked or
clogged chimney opening.
Improper use of appliance/device:
operating a barbecue grill or vehicle
in an enclosed area (like a garage or
screened porch).
Transient CO Problems:
“transient” or on-again-off-again CO problems
can be caused by outdoor conditions and other special circumstances.
The following conditions can result in transient CO situations:
1. Excessive spillage or reverse venting of fuel appliances caused by
outdoor conditions such as:
• Wind direction and/or velocity, including high, gusty winds. Heavy
air in the vent pipes (cold/humid air with extended periods
between cycles).
• Negative pressure differential resulting from the use of exhaust
fans.
• Several appliances running at the same time competing for limit-
ed fresh air.
• Vent pipe connections vibrating loose from clothes dryers, fur-
naces, or water heaters.
• Obstructions in or unconventional vent pipe designs which can
amplify the above situations.
2. Extended operation of unvented fuel burning devices (range, oven,
fireplace).
3. Temperature inversions, which can trap exhaust close to the
ground.
4. Car idling in an open or closed attached garage, or near a home.
These conditions are dangerous because they can trap exhaust in your
home. Since these conditions can come and go, they are also hard to
recreate during a CO investigation.
HOW CAN I PROTECT MY FAMILY FROM
CO POISONING?
A CO Alarm is an excellent means of protection. It monitors the air
and sounds a loud alarm before Carbon Monoxide levels become
threatening for average, healthy adults.
A CO Alarm is not a substitute for proper maintenance of home
appliances.
To help prevent CO problems and reduce the risk of CO poisoning:
• Clean chimneys and flues yearly. Keep them free of debris,
leaves, and nests for proper air flow. Also, have a professional
check for rust and corrosion, cracks, or separations. These con-
ditions can prevent proper air movement and cause backdrafting.
Never “cap” or cover a chimney in any way that would block air
flow.
• Test and maintain all fuel-burning equipment annually. Many
local gas or oil companies and HVAC companies offer appliance
inspections for a nominal fee.
• Make regular visual inspections of all fuel-burning appliances.
Check appliances for excessive rust and scaling. Also check the
flame on the burner and pilot lights. The flame should be blue. A
yellow flame means fuel is not being burned completely and CO
may be present. Keep the blower door on the furnace closed.
Use vents or fans when they are available on all fuel-burning
appliances. Make sure appliances are vented to the outside. Do
not grill or barbecue indoors, or in garages or on screen porches.
• Check for exhaust backflow from CO sources. Check the draft
hood on an operating furnace for a backdraft. Look for cracks on
furnace heat exchangers.
• Check the house or garage on the other side of shared wall.
• Keep windows and doors open slightly. If you suspect that CO
is escaping into your home, open a window or a door. Opening
windows and doors can significantly decrease CO levels.
In addition, familiarize yourself with all enclosed materials. Read
this manual in its entirety, and make sure you understand what to
do if your CO Alarm sounds.
Features:
•
Sealed-In Lithium
Battery — Sealed-in
lithium power supply;
no battery replacement
required over the 10
year life of the alarm.
USER’S MANUAL
RECOMMENDED PLACEMENT
NOTE: For any location, make sure no door or other obstruction could
keep carbon monoxide from reaching the Alarm.
Installing CO Alarms in Mobile Homes
For minimum security install one CO Alarm as close to each sleeping
area as possible. For more security, put one unit in each room. Many
older mobile homes (especially those built before 1978) have little or no
insulation. If your mobile home is not well insulated, or if you are unsure
of the amount of insulation, it is important to install units on inside walls
only.
WHERE THIS ALARM SHOULD NOT BE INSTALLED
Do NOT locate this CO Alarm:
•
In garages, furnace rooms, crawl spaces and unfinished attics.
Avoid extremely dusty, dirty or greasy areas.
•
Where combustion particles are produced. Combustion particles
form when something burns. Areas to avoid include poorly ventilated
kitchens, garages, and furnace rooms. Keep units at least 20 feet
(6 meters) from the sources of combustion particles (stove, furnace,
water heater, space heater) if possible. In areas where a 20-foot
(6 meter) distance is not possible – in modular, mobile, or smaller
homes, for example – it is recommended the Alarm be placed as
far from these fuel-burning sources as possible. The placement
recommendations are intended to keep these Alarms at a
reasonable distance from a fuel-burning source, and thus reduce
“unwanted” alarms. Unwanted alarms can occur if a CO Alarm is
placed directly next to a fuel-burning source. Ventilate these areas
as much as possible.
•
In direct sunlight.
•
In turbulent air, like near ceiling fans or open windows. Blowing air
may prevent CO from reaching the sensors.
•
In areas where temperature is colder than 40˚ F (4.4˚ C) or hotter
than 100˚ F (37.8˚ C). These areas include non-airconditioned crawl
spaces, unfinished attics, uninsulated or poorly insulated ceilings,
porches, and garages.
•
In insect infested areas. Insects can clog the openings to the
sensing chamber.
•
Less than 12 inches (305 mm) away from fluorescent lights.
Electrical “noise” can interfere with the sensor.
•
In “dead air” spaces. See “Avoiding Dead Air Spaces”.
AVOIDING DEAD AIR SPACES
“Dead air” spaces may prevent CO from reaching the CO Alarm. To
avoid dead air spaces, follow installation recommendations below.
INSTALLATION
WHERE TO INSTALL THIS ALARM
The National Fire Protection Association (NFPA) recommends that a CO
Alarm should be centrally located outside of each separate sleeping
area in the immediate vicinity of the bedrooms. For added protection,
install additional CO Alarms in each separate bedroom, and on every
level of your home.
NOTE: For added protection, install an additional CO Alarm at least
15 feet (4.6 meters) away from the furnace or fuel burning heat source
where possible. In smaller homes or in manufactured homes where this
distance cannot be maintained, install the Alarm as far away as possible
from the furnace or other fuel burning source. Installing the Alarm closer
than 15 feet (4.6 meters) will not harm the Alarm, but may increase the
frequency of unwanted alarms.
In general, install Carbon Monoxide Alarms:
•
On every level of your home, including finished attics and basements.
•
In the hall near every sleeping area. If a hall is more than 40 feet (12
meters) long, install a unit at each end.
•
At the top of first-to-second floor stairs.
•
At the bottom of the basement stairs.
•
For additional coverage, install Alarms in all rooms, halls, and
storage areas, where temperatures normally remain between 40˚ F
and 100˚ F (4.4˚ C and 37.8˚ C).
HOW TO INSTALL THIS ALARM
This Alarm was designed to be mounted on the wall or a tabletop.
You must install this device as outlined below. Read “Where To Install
This Alarm” before starting.
Tools you will need: pencil, drill with 3/16” or 5mm drill bit,
flathead screwdriver, hammer.
• Do not connect this unit to any other alarm or auxiliary device.
It is a single-station unit that cannot be linked to other devices.
Connecting anything else to this unit may prevent it from
working properly.
SUGGESTED AREAS FOR INSTALLING
SMOKE ALARMS, CO ALARMS, AND COMBO UNITS
SMOKE ALARM WITH
SILENCE FEATURE
CO ALARMS
BOTH, OR COMBINATION
SMOKE/CO ALARMS
SMOKE ALARMS
KEY:
Suggested locations are based on
NFPA recommendations (NFPA 72
for Smoke Alarms and NFPA 720 for
Carbon Monoxide Alarms). Always
refer to national and local codes
before beginning any installation.
In new construction AC and AC/DC smoke alarms MUST
be interconnected to meet NFPA recommendations.
Type of Alarm
Carbon Monoxide (CO)
What You See and Hear
CO LED:
Flashes Red
Horn:
4 beeps, pause, 4 beeps,
pause
IF THE CO ALARM SOUNDS
Actuation of your CO Alarm indicates the presence of carbon
monoxide (CO) which can kill you. In other words, when your CO
Alarm sounds, you must not ignore it!
IF THE CO ALARM SIGNAL SOUNDS:
1. Press the Test/Silence button.
2. Call your emergency services, fire department or 911. Write down
the number of your local emergency service here:
____________________________________________________________
3. Immediately move to fresh air—outdoors or by an open door or
window. Do a head count to check that all persons are accounted
for. Do not re-enter the premises, or move away from the open door
or window until the emergency services responder has arrived, the
premises have been aired out, and your CO Alarm remains in its
normal condition.
4. After following steps 1-3, if your CO Alarm reactivates within a
24-hour period, repeat steps 1-3 and call a qualified appliance
technician to investigate for sources of CO from fuel-burning
equipment and appliances, and inspect for proper operation of this
equipment. If problems are identified during this inspection have the
equipment serviced immediately. Note any combustion equipment
not inspected by the technician, and consult the manufacturers’
instructions, or contact the manufacturers directly, for more
information about CO safety and this equipment. Make sure that
motor vehicles are not, and have not, been operating in an attached
garage or adjacent to the residence. Write down the number of a
qualified appliance technician here:
____________________________________________________________
NOTE: A qualified appliance technician is defined as “a person, firm,
corporation, or company that either in person or through a representa-
tive, is engaged in and responsible for the installation, testing, servicing,
or replacement of heating, ventilation, air conditioning (HVAC) equipment,
combustion appliances and equipment, and/or gas fireplaces or other
decorative combustion equipment.”
“ALARM-MOVE TO FRESH AIR”
If you hear the CO alarm horn and the CO red light is flashing,
move everyone to a source of fresh air.
DO NOT deactivate the alarm!
USING THE SILENCE FEATURES
Never deactivate the unit to quiet an unwanted alarm. Deactivating
the alarm disables the unit and removes your protection.
The Silence Feature is intended to temporarily silence the horn while
you identify and correct the problem. Do not use the Silence Feature in
emergency situations. It will not correct a CO problem.
The Silence Feature can temporarily quiet an unwanted alarm for several
minutes. Press the Test/Silence button on the alarm cover for at least
3-5 seconds.
After the Test/Silence button is released, the Red LED blinks during the
silence mode.
When the CO Alarm is Silenced
The CO Alarm will remain silent for up to 4 minutes. After 4 minutes, if
CO levels remain potentially dangerous the horn will start sounding
again.
IF YOUR CO ALARM SOUNDS
UL STD 2034
CONFORMS TO
SILENCING THE LOW BATTERY WARNING
This silence feature can temporarily quiet the low battery warning
“chirp” for up to 8 hours. Press the Test/Silence button on the alarm
cover.
Once the low battery warning “chirp” silence feature is activated, the
unit continues to flash the Green light once a minute for 8 hours. After
8 hours, the low battery “chirp” will resume. Replace the Alarm as
soon as possible; this unit will not operate without battery power!
To deactivate this feature: Press the Test/Silence button again. The
unit will go into Test Mode and the low battery warning will resume
(LED flashes and unit sounds “chirp” once a minute).
SILENCING THE END OF LIFE SIGNAL
This silence feature can temporarily quiet the End of Life warning
“chirp” for up to 2 days. You can silence the End of Life warning “chirp”
by pressing the Test/Silence button. The horn will chirp, acknowledging
that the End of Life silence feature has been activated.
After approximately 2 days, the End of Life “chirp” will resume.
REGULAR MAINTENANCE
This unit has been designed to be as maintenance free as possible, but
there are a few simple things you must do to keep it working properly.
•
Test it at least once a week.
•
Clean the CO Alarm at least once a month; gently vacuum the
outside of the CO Alarm using your household vacuum’s soft brush
attachment. A can of clean compressed air (sold at computer or
office supply stores) may also be used. Follow manufacturer
instructions for use. Test the CO Alarm. Never use water, cleaners
or solvents since they may damage the unit.
•
If the CO Alarm becomes contaminated by excessive dirt, dust
and/or grime, and cannot be cleaned to avoid unwanted alarms,
replace the unit immediately.
•
Relocate the unit if it sounds frequent unwanted alarms. See
“Where This Alarm Should Not Be Installed” for details.
Actual battery service life depends on the CO Alarm and the environment
in which it is installed. Regardless of the manufacturer’s suggested
battery life, you MUST replace the Alarm immediately once the unit
starts “chirping” (the “low battery warning”).
WEEKLY TESTING
•
The built-in test switch accurately tests the unit’s operation as
required by Underwriters Laboratories, Inc. (UL). NEVER use
vehicle exhaust! Exhaust may cause permanent damage and
voids your warranty.
•
DO NOT stand close to the alarm when the horn is sounding.
Exposure at close range may be harmful to your hearing. When
testing, step away when horn starts sounding.
It is important to test this unit every week to make sure it is working
properly. Using the test button is the recommended way to test this
CO Alarm:
Press and hold the Test/Silence button 3-5 seconds until unit starts to
alarm. During testing, you will see and hear the following:
The Horn will sound 4 beeps, pause, 4 beeps. The LED flashes Red.
If the unit does not alarm, make sure it has been activated
correctly, and test again. If the unit still does not alarm, replace
it immediately.
1
Test/Silence Button
2
Power/CO Alarm LED
PARTS OF THIS CO ALARM
1
Mounting bracket
2
Mounting slots
FOR WALL MOUNTING
FOLLOW THESE SIMPLE STEPS:
1. Turn alarm upside down so the circular
shape is located in the upper left corner of
the alarm.
2. If mounting bracket is attached to alarm, lift
to separate it from the base.
3. Hold the mounting bracket against the
wall so the arrow located on the mounting
plate is pointing to the left. (The circular
shape will now be in upper right-hand
corner). Trace around the insides of the
mounting slots.
4. Put the unit where it won’t get covered
with dust when you drill the mounting
holes.
5. Using a 3/16” (5 mm) drill bit, drill a hole through the center of the
oval outlines you traced in step #3.
6. Insert the plastic screw anchors (in the plastic bag with screws) into
the holes. Tap the screw anchors gently with a hammer, if necessary,
until they are flush with the wall.
7. Line the mounting bracket up over the plastic screw anchors.
Screw the mounting bracket to the ceiling or wall through the
mounting slots using the two screws provided.
8. Activate the battery. Move the activation switch to
“ON” position against tab stop. Unit will not mount
on mounting bracket unless activated. Once unit is
activated, it cannot be turned off.
NOTE: After you activate the battery, the power indicator light may
flash. (If the unit alarms, the light will blink rapidly, and the horn will
repeatedly sound 4 beeps, pause, 4 beeps.)
9. Attach the CO Alarm to the mounting
bracket. Hold alarm as shown in
diagram. Place alarm on mounting
bracket and slide to the right until
locked into place.
NOTE: Once the CO Alarm is snapped
onto the mounting bracket, you can
rotate the CO Alarm to adjust the
alignment.
10. Test the CO Alarm. See “Weekly Testing.”
11. After 10 years of operation or Low Battery
warning, deactivate the Alarm: Insert a tool
below edge where shown and break tab.
Then slide activation switch to discharge mode.
NOTE: At end of life or low battery indication (chirp): unit must be
put in to deactivation mode to discharge remaining stored energy
in battery. Unit will no longer function once put into this mode.
Unit will resist re-mounting.
TABLETOP PLACEMENT:
Your CO Alarm may also be placed on a tabletop by fastening the 2
stands provided. If using this approach, be sure the Alarm is no more
than 3 feet (0.9 meters) from the floor to minimize the risk of causing
permanent damage to the Alarm in the event it accidently falls to the
ground.
Continued...
NOTE: Be sure to mount the product in the orientation specified in
the next steps as this provides the most stability for mounting the
product to the wall. This CO Alarm can either be wall mounted or
placed on a tabletop.
OFF - ON - DISCHARGE
WHAT YOU NEED TO KNOW ABOUT CO
WHAT IS CO?
CO is an invisible, odorless, tasteless gas produced when fossil fuels
do not burn completely, or are exposed to heat (usually fire). Electrical
appliances typically do not produce CO.
These fuels include: Wood, coal, charcoal, oil, natural gas, gasoline,
kerosene, and propane.
Common appliances are often sources of CO. If they are not properly
maintained, are improperly ventilated, or malfunction, CO levels can
rise quickly. CO is a real danger now that homes are more energy
efficient. “Air-tight” homes with added insulation, sealed windows,
and other weatherproofing
can “trap” CO inside.
SYMPTOMS OF CO POISONING
These symptoms are related to CO POISONING and should be
discussed with ALL household members.
Mild Exposure: Slight headache, nausea, vomiting, fatigue (“flu-like”
symptoms).
Medium Exposure: Throbbing headache, drowsiness, confusion, fast
heart rate.
Extreme Exposure: Convulsions, unconsciousness, heart and lung
failure. Exposure to Carbon Monoxide can cause brain damage, death.
This CO Alarm measures exposure to CO over time. It alarms if CO
levels are extremely high in a short period of time, or if CO levels reach
a certain minimum over a long period of time. The CO Alarm generally
sounds an alarm before the onset of symptoms in average, healthy
adults. Why is this important? Because you need to be warned of a
potential CO problem while you can still react in time. In many reported
cases of CO exposure, victims may be aware that they are not feeling
well, but become disoriented and can no longer react well enough to
exit the building or get help. Also, young children and pets may be the
first affected. The average healthy adult might not feel any symptoms
when the CO Alarm sounds. However, people with cardiac or respiratory
problems, infants, unborn babies, pregnant mothers, or elderly people
can be more quickly and severely affected by CO. If you experience
even mild symptoms of CO poisoning, consult your doctor immediately!
REGULATORY INFORMATION FOR
CO ALARMS
WHAT LEVELS OF CO CAUSE AN ALARM?
Underwriters Laboratories Inc. Standard UL2034 requires residential
CO Alarms to sound when exposed to levels of CO and exposure times
as described below. They are measured in parts per million (ppm) of
CO over time (in minutes).
UL2034 Required Alarm Points*:
• If the alarm is exposed to 400 ppm of CO, IT MUST ALARM
BETWEEN 4 and 15 MINUTES.
• If the alarm is exposed to 150 ppm of CO, IT MUST ALARM
BETWEEN 10 and 50 MINUTES.
• If the alarm is exposed to 70 ppm if CO, IT MUST ALARM
BETWEEN 60 and 240 MINUTES.
* Approximately 10% COHb exposure at levels of 10% to 95% Relative
Humidity (RH).
The unit is designed not to alarm when exposed to a constant level
of 30 ppm for 30 days.
CO Alarms are designed to alarm before there is an immediate life
threat. Since you cannot see or smell CO, never assume it’s not present.
•
An exposure to 100 ppm of CO for 20 minutes may not affect
average, healthy adults, but after 4 hours the same level may cause
headaches.
•
An exposure to 400 ppm of CO may cause headaches in average,
healthy adults after 35 minutes, but can cause death after 2 hours.
Standards:
Underwriters Laboratories Inc. Single and Multiple Station
carbon monoxide alarms UL2034.
According to Underwriters Laboratories Inc. UL2034, Section 1-1.2:
“Carbon monoxide alarms covered by these requirements are intended
to respond to the presence of carbon monoxide from sources such as,
but not limited to, exhaust from internal-combustion engines, abnormal
operation of fuel-fired appliances, and fireplaces. CO Alarms are intended
to alarm at carbon monoxide levels below those that could cause a loss
of ability to react to the dangers of Carbon Monoxide exposure.” This
CO Alarm monitors the air at the Alarm, and is designed to alarm before
CO levels become life threatening. This allows you precious time to
leave the house and correct the problem. This is only possible if Alarms
are located, installed, and maintained as described in this manual.
Gas Detection at Typical Temperature and Humidity Ranges:
The
CO Alarm is not formulated to detect CO levels below 30 ppm typically.
UL tested for false alarm resistance to Methane (500 ppm), Butane (300
ppm), Heptane (500 ppm), Ethyl Acetate (200 ppm), Isopropyl Alcohol
(200 ppm) and Carbon Dioxide (5000 ppm). Values measure gas and
vapor concentrations in parts per million.
Audible Alarm: 85 dB minimum at 10 feet (3 meters).
This CO Alarm is intended for residential use. It is not intended for
use in industrial applications where Occupational Safety and Health
Administration (OSHA) requirements for Carbon Monoxide Alarms must
be met. This device is not intended to alert hearing impaired residents.
CO Alarms are not yet available for the hearing impaired.
CO Alarms may not waken all individuals. Practice the escape plan
at least twice a year, making sure that everyone is involved – from kids
to grand-parents. Allow children to master fire escape planning and
practice before holding a fire drill at night when they are sleeping.
If children or others do not readily waken to the sound of the CO Alarm,
or if there are infants or family members with mobility limitations,
make sure that someone is assigned to assist them in the event of an
emergency. It is recommended that you hold a fire drill while family
members are sleeping in order to determine their response to the
sound of the CO Alarm while sleeping and to determine whether they
may need assistance in the event of an emergency.
This CO Alarm will not sense CO that does not reach the sensors.
It will only sense CO at the sensor. CO may be present in other areas.
Doors or other obstructions may affect the rate at which CO reaches the
sensors. If bedroom doors are usually closed at night, we recommend
you install a CO Alarm in each bedroom and in the hallway between
them.
This CO Alarm may not sense CO on another level of the home.
Example: This alarm device, installed on the second floor, may not
sense CO in the basement. For this reason, one alarm device may not
give adequate early warning.
CO Alarms may not be heard. The alarm horn loudness meets or
exceeds current UL standards of 85 dB at 10 feet (3 meters). However,
if the CO Alarm is installed outside the bedroom, it may not wake up a
sound sleeper or one who has recently used drugs or has been drinking
alcoholic beverages. This is especially true if the door is closed or only
partly open. Even persons who are awake may not hear the alarm horn
if the sound is blocked by distance or closed doors. Noise from traffic,
stereo, radio, television, air conditioner, or other appliances may also
prevent alert persons from hearing the alarm horn. This CO Alarm is not
intended for people who are hearing impaired.
This CO Alarm is not a substitute for life insurance. Though this CO
Alarm warns against increasing CO levels, BRK Brands, Inc. does not
warrant or imply in any way that they will protect lives. Homeowners
and renters must still insure their lives.
This CO Alarm has a limited life.
Although this CO Alarm and all
of its parts have passed many stringent tests and are designed to
be as reliable as possible, any of these parts could fail at any time.
Therefore, you must test this device weekly. The unit should be
replaced immediately if it is not operating properly.
This CO Alarm is not foolproof.
Like all other electronic devices,
this CO Alarm has limitations. It can only detect CO that reaches the
sensors. It may not give early warning of the source of CO is in a
remote part of the home, away from the alarm device.
GENERAL LIMITATIONS OF CO ALARMS
TROUBLESHOOTING GUIDE
If the Alarm...
Problem...
You should...
Horn "chirps" about once per minute.
Low battery warning.
Immediately replace the Alarm.
Horn does three "chirps" every minute;
LED has 3 rapid Green flashes with "chirps".
MALFUNCTION SIGNAL. Device is not
working properly, and needs to be replaced.
Units under warranty should be returned to
manufacturer for replacement. See “Limited
Warranty” for details.
Carbon Monoxide Alarm ONLY:
CO Alarm goes back into alarm 4 minutes after
you Silence it.
CO levels indicate a potentially dangerous
situation.
IF YOU ARE FEELING SYMPTOMS OF CO
POISONING, EVACUATE your home and call
911 or the Fire Department. Refer to "If The CO
Alarm Sounds" for details.
CO Alarm sounds frequently even though no high
levels of CO are revealed in an investigation.
The CO Alarm may be improperly located. Refer
to “Where to Install This Alarm” for details.
Relocate your Alarm. If frequent alarms
continue, have home rechecked for potential
CO problems. You may be experiencing an
intermittent CO problem.
If you have questions that cannot be answered by reading this manual, call Consumer Affairs at 1-800-323-9005, M-F 7:30 a.m. to 5:00 p.m. (CST)
The light flashes GREEN and the horn sounds
5 “chirps” every minute.
END OF LIFE SIGNAL.
Alarm needs to be replaced.
Immediately replace the Alarm.
LIMITED WARRANTY
BRK Brands, Inc., ("BRK") the maker of First Alert
®
brand products warrants that for a period of ten years from the date of purchase, this product will
be free from defects in material and workmanship. BRK, at its option, will repair or replace this product or any component of the product found to be
defective during the warranty period. Replacement will be made with a new or remanufactured product or component. If the product is no longer available,
replacement may be made with a similar product of equal or greater value. This is your exclusive warranty. This warranty is valid for the original retail
purchaser from the date of initial retail purchase and is not transferable. Keep the original sales receipt. Proof of purchase is required to obtain warranty
performance. BRK dealers, service centers, or retail stores selling BRK products do not have the right to alter, modify or any way change the terms and
conditions of this warranty.
This warranty does not cover normal wear of parts or damage resulting from any of the following: negligent use or misuse of the product, use on improper
voltage or current, use contrary to the operating instructions, disassembly, repair or alteration by anyone other than BRK or an authorized service center.
Further, the warranty does not cover Acts of God, such as fire, flood, hurricanes and tornadoes or any batteries that are included with this unit.
BRK shall not be liable for any incidental or consequential damages caused by the breach of any express or implied warranty. Except to the extent
prohibited by applicable law, any implied warranty of merchantability or fitness for a particular purpose is limited in duration to the duration of the above
warranty. Some states, provinces or jurisdictions do not allow the exclusion or limitation of incidental or consequential damages or limitations on how
long an implied warranty lasts, so the above limitations or exclusion may not apply to you. This warranty gives you specific legal rights, and you may
also have other rights that vary from state to state or province to province.
How to Obtain Warranty Service
Service: If service is required, do not return the product to your retailer. In order to obtain warranty service, contact the Consumer Affairs Division at
1-800-323-9005, 7:30 AM - 5:00 PM Central Standard Time, Monday through Friday. To assist us in serving you, please have the model number and
date of purchase available when calling.
For Warranty Service return to: BRK Brands, Inc., 25 Spur Drive, El Paso, TX 79906
Disposal: Waste electrical products should not be disposed of with regular household waste. Please recycle where facilities exist.
Check local requirements for disposal of Li-Ion electronic devices.
The Alarm should be deactivated before disposal. See page 2, step 11.
You can also return your Alarm to us for disposal. For return address see above.
Please include a note confirming the product is being returned for disposal.
For your records, please record:
Date Purchased: _________________
Where Purchased: __________________________________
Date Installed: ____________/____________Month/Year
Replace alarm 10 years after installation. Please write the date in
the space provided:
_____________/____________Month/Year
The alarm will also provide an audible End-of-Life Signal
approximately 10 years after installation to remind you to
replace the unit.
The End-of-Life Signal can be silenced for up to 2 days.
Do not unplug or deactivate the alarm until you get replacement.
Printed in Mexico M08-0477-001 K1
01/14
First Alert
®
is a registered trademark of the First Alert Trust.
TABLE TOP PLACEMENT, Continued
To Attach Tabletop Stands:
1. Hold alarm as shown in diagram.
2. Insert bottom hook of tabletop stand into slot on bottom
of alarm. Snap top hook into place.
Repeat step #1 & #2 to attach remaining
stand.
NOTE: Mounting bracket must be
removed in order to attach tabletop
stands.
