background image

Installation, Operation and Maintenance

1.5 Through 5 Ton 
Split System Air Conditioner

INTRODUCTION ..............................................................................1

NOTES TO INSTALLER ....................................................................1

RECOGNIZE SAFETY SYMBOLS, WORDS AND LABELS ................1

CODES ............................................................................................1

INSPECTION AND UNPACKING ......................................................1

INSTALLATION

Clearances ..........................................................................2
Support ..............................................................................2
Exposure ............................................................................2
Proximity to Evaporator....................................................2

ELECTRICAL CONNECTIONS ..........................................................2

SERVICE VALVE CONNECTIONS

Braze Joints ..............................................................................3
Evacuation ................................................................................3
Opening the Service Valve (Step  Valve) ................................3

REFRIGERANT PIPING ...................................................................4

Precautions ................................................................................4
Liquid Line Sizes........................................................................4
Suction Line Sizes......................................................................4

SUBCOOLING CHARGING  ............................................................5
OPERATION INSTRUCTIONS ..........................................................6
MAINTENANCE INSTRUCTIONS ....................................................6

CONDENSING UNIT NOMENCLATURE ..........................................7

CIRCUIT DIAGRAM ....................................................................... 6

NOTE: 

THESE INSTRUCTIONS ARE INTENDED AS AN AID TO QUALIFIED
SERVICE PERSONNEL FOR PROPER INSTALLATION, ADJUSTMENT
AND OPERATION OF THIS EQUIPMENT. READ THE ENTIRE
INSTRUCTION MANUAL THOROUGHLY BEFORE ATTEMPTING
INSTALLATION OR OPERATION.

TABLE OF CONTENTS

 

R-410A Refrigerant

THIS UNIT USES:

See precautions on page 5

R-410A Refrigerant precautions  .................................................5

IOMCDU1-F.1GB

Summary of Contents for C18ABZ1VF









Reviews: