FBD FBD550 Installation, Operation And Service Manual Download | Manualshive

Page: 1 / 37

background image

INSTALLATION, OPERATION, AND SERVICE MANUAL

FOR THE

MODEL FBD550

FROZEN BEVERAGE DISPENSER

SPECIFICATIONS

DIMENSIONS

Width

17.0 inches

(432 mm)

Depth

32.3 inches

(820 mm)

Height (Standard Countertop Unit)

34.0 inches

(864 mm)

Height (Optional Roll Around Unit/Stand)

68.0 inches (1727 mm)

WEIGHT

Shipping

395 pounds

(179.2 kg)

Empty

318 pounds

(144.2 kg)

Operational

345 pounds

(156.5 kg)

WATER REQUIREMENTS

Minimum flowing pressure

30 PSIG

(207.0 KPa)

Maximum static pressure

70 PSIG

(483.0 KPa)

CARBON DIOXIDE (CO

2

) REQUIREMENTS

Minimum pressure

70 PSIG

(483.0 KPa)

Maximum pressure

75 PSIG

(517.5 KPa)

NOTICE:

The information contained in this document is subject to change without notice.

FBD MAKES NO WARRANTY OF ANY KIND WITH REGARD TO THIS MATERIAL, INCLUDING, BUT NOT LIMIT-
ED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR
PURPOSE. FBD shall not be liable for errors contained herein or for incidental consequential damages in connection with the
furnishings, performance, or use of this material.

This document contains proprietary information which is protected by copyright. All rights reserved.

© Copyright 2006 by FBD, all rights reserved.

This manual supersedes FBD Manual 24-0276-0003, dated 01/31/05.

Revision:

10-25-06

FBD Part Number:

24-0276-0003

THIS DOCUMENT CONTAINS IMPORTANT INFORMATION

This manual must be read and understood before the installation and operation of this dispenser.

Check out the FBD web site:

www.fbdfrozen.com

FBD Partnership, LP

•

P.O. BOX 18597.

•

SAN ANTONIO, TX 78218 USA

•

•

210-637-2800

•

FAX 210-637-2844

•

www.fbdfrozen.com

•

•

FBD TECHNICAL SUPPORT • 1-866-323-2777 • TECHNICAL SUPPORT FAX 1-210-637-2832

1
2
3
...
»

Summary of Contents for FBD550






































Reviews:

No comments

Related manuals for FBD550

Brand: SANSTAND Pages: 2

Brand: BIELMEIER Pages: 68

Brand: Inta Pages: 8

Brand: Keg King Pages: 5

ZIPPETTE PRO Series

Brand: JENCONS Pages: 48

Brand: Hydrotech Pages: 23

Brand: Lacava Pages: 10

Brand: AOX Pages: 4

Brand: Knight Pages: 20

Brand: Polar Refrigeration Pages: 12

Brand: Modena Pages: 23

Brand: U-Line Pages: 9

Brand: WFA Pages: 2

diamond 7-LX-100B

Brand: Lancaster Pages: 30

Brand: VALCO MELTON Pages: 123

Brand: Dahlert Pages: 48

TECHCON SYSTEMS TS250

Brand: OK International Pages: 17

Brand: RAMTONS Pages: 7

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands