1
IMPO
RTAN
T:
Go to www
.extron.com f
or the complete
user guide
, installation instructions,
and
specifications bef
ore connecting the
product to the po
wer sour
ce.
XTP T UWP 202 • Setup Guide
The XTP T UWP 202 is a two-input XTP decorator-style wallplate transmitter that can be installed into the provided mud ring or a UL Listed metal
junction box. This guide provides instructions for an experienced installer to install and connect the XTP T UWP 202.
Throughput and Control
Connections
Power Connection,
Reset Button, and
Input Connections
A
XTP output connector
B
RS-232 and IR Over
XTP connector
C
Remote RS-232
connector
D
LAN connector (LAN
model only)
E
USB configuration
connector
F
DC power connector
G
Reset button
H
HDMI input
connector
I
Analog audio input
connector
J
Female 15-pin HD
connector
Figure 1.
XTP T UWP 202 Rear (Left) and Front (Right) Panel Features (LAN Model)
Installation
NOTE:
If using a junction box, use a metal box only.
•
Ensure the installation meets the building, electrical, and safety codes.
•
For additional mounting considerations, see the
XTP T UWP 202
User Guide
at
www.extron.com
. For metal junction boxes, refer to the
manufacturer for additional mounting instructions and considerations.
ATTENTION:
•
Do not mount multiple devices adjacent to each other in the
same metal junction box. Add at least a one gang space
between devices.
•
Ne procédez pas à une installation juxtaposée des appareils
dans le même boîtier de dérivation métallique. Veuillez
laisser un espace d’un gang minimum entre chaque
appareil.
Wall Mount Preparation
1.
Using a soft pencil, mark cut guidelines on the mounting surface. For
accuracy, use a template or the mounting enclosure.
NOTE:
Install junction boxes against a wall stud (see figure 2).
2.
Cut a hole in the wall. To avoid making the hole too big, cut inside the
marked lines.
3.
If using the mud ring in a wall with insulation inside, remove at least
6 inches of the insulation in all directions around the cutout. If a wall
stud interferes with removing the insulation, remove as much as
possible between the cutout and the wall stud.
4.
Test the fit by inserting the mud ring or metal junction box into the hole
in the wall. If necessary, enlarge the hole as needed.
5.
Install the UL Listed junction box or mud ring.
•
UL Listed metal junction box
— Use mounting screws to fasten
the box to a wall stud (see figure 2).
•
Mud ring
— Attach the mounting screws to the mud ring and
loosely attach backing clips to the ends of the screws (see
figure 3). Fit the mud ring in the opening and then rotate the
backing clips until they fit snugly against the back of the wall.
Tx
RS-232
XTP T UWP 202
RS-232
IR
Rx
Tx Rx
G
Tx Rx G
12V
1.0 A MAX.
POWER
OVER XTP
XTP OUT
REMOTE
PWR HDCP HDMI
HDMI IN
LAN
VGA
RESET
CONFIG
AUDIO
CLIP
AUTO
SWITCH
AUDIO IN
VGA IN
B C F
A
H
D
E
I
G
Rear
Front
J
XTP T UWP 202
Signal Output
Cable
Cable
Clamp
Decorator-Style Faceplate
Screws or
Nails
Wall opening is
flush with edge
of box.
Wall Stud
PWR
HDC
P H
DMI
HDMI
IN
LAN
VGA
RESET
CON
FIG
AU
DIO
CL
IP
AUTO
SWITCH
AUDI
O IN
VGA IN
Figure 2.
Metal Junction Box Installation
Backing Clip
Mounting Screw
Rotate the backing clip
out of the way to insert
the mud ring into the wall.
XTP T UWP 202
Decorator-Style Faceplate
PWR
HDC
P H
DMI
HDMI
IN
LAN
VGA
RESET
CON
FIG
AU
DIO
CL
IP
AUTO
SWITCH
AUDIO IN
VGA IN
Figure 3.
Mud Ring Installation
