1
IMPO
RTAN
T:
IMPO
RTAN
T:
Go to
www.e
xtron.com
for the
product specifications.
NAV 10E 501 and NAV 10E 101 • Setup Guide
CLASS 1 LASER PRODUCT,
see
NAV 10E 501 and NAV 10E 101
User Guide
at
WARNING:
The NAV 10E 501 and NAV 10E 101 output continuous invisible light (Class 1 rated), which may be harmful to the
eyes; use with caution.
•
Do not look into the fiber optic cable connectors or into the fiber optic cables themselves.
•
Plug the attached dust caps into the optical transceivers when the fiber cable is unplugged.
AVERTISSEMENT :
Le NAV 10E 501 et le NAV 10E 101 émettent une lumière invisible en continu (équipement de classe 1) qui peut
être dangereuse pour les yeux ; à utiliser avec précaution.
•
Ne pas fixer directement les connecteurs optiques ou les câbles fibre optique.
•
Associez les bouchons anti-poussière à l’ensemble émetteur/récepteur optique lorsque le câble fibre optique est débranché.
This guide provides instructions for an experienced installer to install the Extron NAV 10E 501 and NAV 10E 101 streaming encoders and
to make all connections. The Extron NAV encoder and one or more compatible decoders form an AV distribution and switching matrix on a
managed 10G IP network.
NOTE
:
For more information on any subject in this guide, see the
NAV 10E 501 and NAV 10E 101 User Guide
, available at
Installation
Step 1 — Mounting
Turn off or disconnect all equipment power sources and rack or furniture mount the encoder as required.
Step 2 — Rear Panel Connections
HDMI
LOOP THRU
POWER
12V
L
CONT
C T Tx Rx G S G
RS-232
IR
R
AUDIO
CONTROL
INPUT
NAV 10E 101
RESET
NAV 10G
LAN
2.0 A MAX
NAV 10G
EXT
HDMI
LOOP THRU
POWER
12V
2.0 A MAX
L
CONT
C T Tx Rx G S G
5V/200 mA
RS-232
IR
R
AUDIO
LAN
USB 2.0
CONTROL
INPUT
NAV 10E 501
RESET
H
H
H
F
F
F
C
C
C
A
A
A
B
B
B
D
D
D
J
J
J
E
E
E
I
I
I
G
G
G
Figure 1.
NAV 10E 501 and NAV 10E 101 Rear Panel Features
A
HDMI input port
— Connect an HDMI cable between this port and the HDMI output port (or DVI port, with an appropriate adapter) of
the digital video source.
B
HDMI Loop Thru port
— Connect a display to this female HDMI connector for local loop-through monitoring of the source signal.
NOTE:
on page 6 to securely fasten the HDMI connectors to the encoder for
A
and
B
.
C
Audio input port
— Connect balanced or unbalanced stereo audio input to this 5-pole, 3.5 mm captive screw connector (see
on page 6 to wire the connector).
D
Control Contact Closure port
— Connect an Extron Show Me
®
cable to this port to allow the encoder to select itself as the input to
the decoder, using the control system.
E
Control RS-232/IR port
— Connect a serial RS-232 signal, a modulated IR signal, or both to this 3.5 mm, 5-pole captive screw
connector for bidirectional RS-232 and unidirectional IR communication with connected remote controlled devices using an Extron
control system (see
on page 6 to wire the connector).
IMPO
RTAN
T:
IMPO
RTAN
T:
Go to www
.extron.com f
or the complete
user guide
, installation instructions,
and
specifications bef
ore connecting the
product to the po
wer sour
ce.
