If you are ready with the jumper settings for the EX-1062/1064/1065, please proceed with
the following installation instructions. Because the designs of computers are different, only
general installation instructions are given. Please refer your computer’s reference manual
whenever in doubt.
1. Turn off the power to your computer and any other connected peripherals.
2. Remove the mounting screws located at the rear and/or sides panels of your Com-
puter and gently slide the cover off.
3. If your pc case do have a front panel please follow the instructions at J5 above.
Normally the cables should be marked if not please ask the front panel manufacturer
4. If necessary please install now the external power supply to the card like shown at
JP2 & J6 above.
5. Locate an available PCI-Express expansion slot and remove its covers from the rear
panel of your computer.
6. Align the EX-1062/1064/1065 with the expansion slot, and then gently but firmly,
insert the card. Make sure the card is seated and oriented correctly.
7. Then connect the card with a screw to the rear panel of the computer.
8. Gently replace your computer’s cover and the mounting screws.
HARDWARE INSTALLATION :
6
5
EX
EX
EX
-
-
-
1062 / 1064 / 1065
1062 / 1064 / 1065
1062 / 1064 / 1065
English
English
English
EX
EX
EX
-
-
-
1062 / 1064 / 1065
1062 / 1064 / 1065
1062 / 1064 / 1065
English
English
English
1
Vielen Dank das Sie sich für eine EXSYS USB 2.0 PCI Karte entschieden haben. Die
EX-1064/1065 ist mit drei externen und einen internen Downstream Port und die EX-
1062 mit zwei externen und einen 10 Pin internen Downstream Port ausgestattet. Die
EX-1065 ist eine Low Profile USB 2.0 PCI Karte mit einem kurzen 8cm Bügel für
schmale Computer Gehäuse. Die USB 2.0 PCI Karten sind voll kompatibel mit Micro-
soft Windows Standard OpenHCD Treibern und sind nach den Normen des Universal
Serial Bus (USB) Rev. 2.0 entwickelt worden. Sie haben einen Dual Speed USB Trans-
ceiver. Sie unterstützen den 32 und 64-Bit PCI-Bus mit 5 Volt und 3,3 Volt. Es wird der
Chipset von NEC verwendet.
BESCHREIBUNG & TECHNISCHE DATEN
:
AUFBAU
:
Kompatibilität:
PCI 32-Bit oder PCI-X 64-Bit
Betriebssysteme:
WIN 9.x/ME/2000/XP/Server 2003/MAC/Vista/(Linux vom OS)
Anschlüsse:
EX-1064/1065
3 x A-Buchse extern, 1 x A-Buchse intern, 1 x 10 Pin Stecker
EX-1062
2 x A-Buchse extern, 1 x 10 Pin Stecker
Lieferumfang:
EX-1062, 1064 oder 1065 , Treiber CD, Anleitung
Zertifikate:
CE
CE
CE
CE
/
FCC / RoHS / WEEE DE97424562 / WHQL
Windows 98 and ME
Please insert the driver CD into your CD-Rom drive (for example D:\ ) and open the
folder
D:\USB 2.0\NEC\WIN9.x
on the CD.
Now start the file
“U2v2_1.exe“
by double click on your mouse and follow the setup
program to finish installation process. After that shut down windows and follow the
instructions for the Hardware installation. After installing the card simply start your
computer and the card will be recognized automatically by your system.
CHECK INSTALLED DRIVER:
Open the
>Device manager<
.
Now you should see at
„USB Devices“
the following new
entry:
<NEC USB Open Host Controller> <PCI USB 2.0 Host Controller> <USB 2.0
Root Hub Device> <USB Root Hub>.
If you see this or a similar information the EX-1062/1064/1065 is installed correctly.
Windows 2000 and 2000 Server
Should you use Windows 2000 with service pack 4 you don’t need any drivers. The
drivers are already integrated in Windows and the EX-1062/1064/1065 will be installed
automatically.
Should you use Windows 2000 without service pack 4 please insert the driver CD into your
CD-Rom drive (for example D:\ ) and open the folder
D:\USB 2.0\NEC\WIN9.x
on the CD.
Now start the file
“U2v2_1.exe“
by double click on your mouse and follow the setup
program to finish installation process. After that shut down windows and follow the
instructions for the Hardware installation. After installing the card simply start your
computer and the card will be recognized automatically by your system.
CHECK INSTALLED DRIVER:
Open the
>Device manager<
.
Now you should see at
„USB Devices“
the following new
entry:
<NEC USB Open Host Controller> <PCI USB 2.0 Host Controller> <USB 2.0
Root Hub Device> <USB Root Hub>.
If you see this or a similar information the EX-1062/1064/1065 is installed correctly.
Windows XP Server 2003 and Vista
Should you use Vista or Windows XP with service pack 1 you don't need any drivers.
The drivers are already integrated in Windows and the EX-1062/1064/1065 will be
installed automatically.
Should you use Windows XP without any service pack please insert the driver CD into
your CD-Rom drive (for example D:\ ) and open the folder
D:\USB 2.0\NEC\WIN9.x
on the
CD.
Now start the file
“U2v2_1.exe“
by double click on your mouse and follow the setup
program to finish installation process. After that shut down windows and follow the
instructions for the Hardware installation. After installing the card simply start your
computer and the card will be recognized automatically by your system.
CHECK INSTALLED DRIVER:
Open the
>Device manager<
.
Now you should see at
„USB Devices“
the following new
entry:
<NEC USB Open Host Controller> <PCI USB 2.0 Host Controller> <USB 2.0
Root Hub Device> <USB Root Hub>.
If you see this or a similar information the EX-1062/1064/1065 is installed correctly.
DRIVER INSTALLATION :
JUMPER
SETTING & CONNECTORS
:
Pin
Signal
Pin
Signal
Pin
Signal
1
VCC1 +5V
5
DATA1+
9
NC
2
VCC2 +5V
6
DATA2+
10
NC
3
DATA1-
7
GND1
USB 2.0 - 10 pin connector ( standard):
4
DATA2-
8
GND2
Attention!!!:
Please make sure that you connect the cable in the right
order like shown in the list above. If you connect the cable
wrong it can destroy your hardware! The labelling on the
cable must match with the ones on our card.
For EX-1064/1065
If you use the internal A-port J4 you can use only one of
the ports from the 10 Pin connector J5!
Attention! If you use Windows 98, ME, 2000 without service pack 4 or XP without
service pack. Please install the drivers for the Ex-11064 / 11065 first.
If you use Windows 2000 including service pack 4, or Windows XP including
service pack 1 & 2. Or you already installed the drivers please proceed with the
following instructions for hardware installation.
J4
Ein Interner
USB 2.0 Port
J5
USB Port
3&4
für Front Anschluss
Anschluss vom Netzteil für
+5V oder +12V Spannung
J4
Ein Interner
USB 2.0 Port
J5
USB Port
3&4
für Front Anschluss
Anschluss vom Netzteil für
+5V oder +12V Spannung
J1-J2
2 x USB 2.0 Port
J3
USB Port
3&4
für Front Anschluss
PCI =
Power from PCI-Express BUS (standard)
AUX =
Power from PC power supply
(For safe direct power from pc power supply to provide suffi-
cient power for devices with high power consumption).
Connector J6 must be connected with PC power suplly!
JP2:
J6:
If JP2 is set to AUX J6 must be connected with pc power
supply! Please make sure you connect the plug in the right
direction. Never connect or release the plug while the PC
power is on!
Only for EX-1064/1065:
P
C
I
A
U
X
+5VCC
Data1-
Data1+
GND
+5VCC
Data2-
Data2+
GND
1
3
5
7
9
J5:
2
4
6
8
10
J1-J5 (EX-1064/1065):
J1-J3 (EX-1062):
USB 2.0 A-female connector:
Pin
Signal
Pin
Signal
1
VCC
3
DATA+
2
DATA-
4
GND
NEC Chip-Set
J1-J3
3 x USB 2.0 Port
EX-1064
NEC Chip-Set
J1-J3
3 x USB 2.0 Port
EX-1065
NEC Chip-Set
EX-1062
Bedienungsanleitung
Bedienungsanleitung
Vers. 1.0 / 16.07.07
