ETC Source Four XT HID Zoom 15-30 User Manual Download | Manualshive

Page: 1 / 20

background image

Copyright © 2011. Electronic Theatre Controls, Inc.

All Rights reserved.

Product information and specifications subject to change.

Part Number:

7065M1200

Rev B

Released: 2011-11

User Manual

Production Dates: May 2011 - Present

Source Four XT HID Zoom 15° to 30°

1
2
3
...
»

Summary of Contents for Source Four XT HID Zoom 15-30





















Reviews:

No comments

Related manuals for Source Four XT HID Zoom 15-30

Brand: PSDK Pages: 13

Knight Spotlight

Brand: Endon Pages: 2

EXL-XL Profile Zoom

Brand: EXALite Pages: 11

SUPER TROUPER III

Brand: Strong Lighting Pages: 46

XENON GLADIATOR IV

Brand: Strong International Pages: 48

XENON GLADIATOR II

Brand: Strong International Pages: 55

Brand: Larson Electronics Pages: 2

iMSP Jupiter Silver

Brand: iMSENS Pages: 5

Brand: ORSTEEL Light Pages: 2

Brand: Light-Point Pages: 2

Brand: WAC Lighting Pages: 5

Brand: SolarGoesGreen Pages: 3

Brand: StonePoint Pages: 4

Brand: Life Pages: 2

SquareLED Hi-Precision 50W

Brand: LTH Pages: 7

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands