background image

Interior of Vehicle

Concealed

Display

(Optional)

12 Volt

Power Line

±

Interior of Vehicle

External

Speaker

(Optional)

Passport SRX Installation Manual

Front Radar Receiver

1

Determine the best location for the radar

receiver. The best location is typically under
the bumper, or inside the front grill of the
vehicle. For the best radar performance, install
the radar receiver horizontally, with a clear
“view” of the road.

2

Using the built-in mounting holes on the

receiver, or the supplied right-angle mounting
bracket, mark location. Drill pilot holes in the
vehicle if necessary.

3

Mount radar receiver using the supplied

hardware. (If right-angle mounting bracket is
used, secure radar receiver to the right-angle
bracket first, then install bracket with radar
receiver to the vehicle.)

Note:
1. Do not drill holes in the receiver itself.
2. Thoroughly investigate location before
drilling any holes.
3. Keep all cables away from moving parts,
and hot surfaces (radiator, hoses, etc.).
4. Do not splice cable.

Radar Receiver Cable

1

Connect the receiver cable to the receiver.

2

Route cable to firewall, and secure with zip-

ties (included).

3

Route receiver cable into the vehicle’s 

interior. If there is not a suitable opening, drill
a 13/32" or 7/16" hole.

4

Pull cable through firewall, and plug

connector into the jack labeled “Front Radar”
on the Interface.

5

Pull grommet (located on the receiver cable

itself) through the firewall to seal the hole.

Use silicone sealant (not supplied) if 
necessary.

Note:
1. Connection between the radar receiver, and
the receiver cable, must be located in a dry
location under hood.
2. Only drill hole in firewall after thoroughly
investigating location first, ensuring no other
wires, hoses, etc. will be damaged.
3. Keep all cables away from moving parts,
and hot surfaces (radiator, hoses, etc.).
4. Do not splice cable.

Display Controller

1

Determine the best location for the Display

Controller in the vehicle’s interior. (Consult
customer if necessary.)

2

Install Display Controller using supplied

velcro, or double-sided tape.

3

Route cable and plug into jack marked

“Display” on Interface.

Note:
1. Make certain that the Display is clearly
visible from the driver’s position, and that the
controls can be easily accessed without 
interfering with normal driving.

Front Laser Shifters

1

Determine best location for the Laser

Shifters. For optimum performance, install
each laser shifter on either side of the front
license plate, with a clear “view” of the road.
If possible, center each shifter module
between the license plate, and the outside
edge of the vehicle. (see photo above)

2

Using the supplied mounting bracket, mark

location. Drill pilot holes in the vehicle if
necessary.

3

Mount the Laser Shifters using the supplied

hardware, making sure that each shifter is
level to the road.

Note:
1. Do not drill holes in the Laser Shifter itself.
2. Thoroughly investigate location before
drilling any holes.
3. Keep all cables away from moving parts,
and hot surfaces (radiator, hoses, etc.)
4. Do not splice cable.
5. Make certain that each Laser Shifter is level,
and has a clear “view” of the road.

Laser Shifter Cables

1

Route Laser Shifter cables to firewall, and

secure with zip-ties (included).

2

Route both Shifter cables into the vehicle’s

interior. If there is not a suitable opening, drill
a 13/32" or 7/16" hole.

3

Pull cables through firewall, and plug

connectors into Y-adapter.

4

Plug Y-adapter into jack marked “Front

Laser/Shifter” on Interface.

5

Pull grommet (located on each cable)

through the firewall to seal the hole. Use 
silicone sealant (not supplied) if necessary.

Note:
1. Only drill hole in firewall after thoroughly
investigating location first, ensuring no other
wires, hoses, etc. will be damaged.
2. Keep all cables away from moving parts,
and hot surfaces (radiator, hoses, etc.).
3. Do not splice cable.

TEST

After all components are installed correctly:

1

Turn Passport on by rotating the volume

control knob.

2

Turn vehicle’s ignition to the “on” position.

3

Passport will cycle through a startup

sequence.

4

If any error messages come up, see page 21

of the Owner’s Manual for details.

Interface

1

Install Interface under the dash using

supplied zip-ties. DO NOT MOUNT IN
ENGINE COMPARTMENT.

2

Connect black wire (-) to ground, and red-

striped wire (+) to a switched 12-volt supply.
(If Passport is left in the “on” position, it will
automatically power on and off with the igni-
tion). Use blue 3M connector (provided) to
tap into existing circuit if needed.

3

Radar receiver, front Laser Shifters, rear

Laser Shifter, and Display Controller all plug
into the Interface. (Be sure to plug all cables
into the correct labeled jacks.)

A

A

C

E

E

H

G

G

A

C

B

B

B

B

B

D

D

D

F

F

Vertical Display Alternative

The Display Controller can be mounted 
vertically, such as the side of the center
console (volume knob goes at the top). To do
so, follow these steps:

1

Carefully remove the standard overlay from

the Display Controller.

2

Replace the standard overlay with the

optional vertical one found inside the Owner’s
Manual.

3

See programming section for changing the

text display to read vertically.

Rear Laser Shifter

1

Remove two license plate screws, (top or

bottom).

2

Mount Laser Shifter to plate using supplied

mounting bracket.

3

Route wire through trunk compartment,

and into the vehicle’s interior.

4

Insert connector to jack labeled “Rear Laser

Shifter” on Interface.

Tips
1. Do not block license plate illumination.
2. Do not cover any required license plate
information.

Installation Alternatives:
1. Can be installed inside the vehicle facing
out the rear window.
2. Cable can be routed under vehicle (keep
away from hot and moving parts) then
brought into the vehicle’s interior.
3. Cable can be cut if necessary for routing.
Reconnect and solder each of the three wires,
and seal with heat-shrink tubing.

Remote Mute

/

Volume Adjust

1

Determine best location for the Remote

Mute Button.

2

Clean surface area.

3

Remove paper backing on the back of the

button, and press onto surface.

4

Route cable and plug into jack marked

“Mute” on Interface.

H

Reviews: