Start Here
4
Load paper
See the online User’s Guide for instructions on loading paper in
the cassette 1 and rear paper slot, available paper types, sizes,
loading capacity, and loading CD/DVD/Blu-ray
™
discs (XP-630/
XP-830).
XP-630/XP-830
Output tray
Cassette 1
Cassette 2/front cover
You can load the following paper sizes:
• Cassette 1: 3.5 × 5-, 4 × 6-, or 5 × 7-inch photo paper
• Cassette 2: Letter-size, A4-, legal-size, or 8 × 10-inch paper
See the instructions below for loading paper.
• Rear paper feed slot: One sheet at a time (XP-830)
XP-530
Output tray
Cassette/front cover
You can load the following paper sizes: 3.5 × 5-, 5 × 7-, 8 × 10-
inch, letter-size, A4-, or legal-size.
1
Lower the front cover (if it’s not open already) and pull on
the front cover to pull out the paper cassette.
2
Slide the side edge guides outward and set the front edge
guide to the paper size you are using.
3
Insert the paper with the glossy or printable side
facedown.
Note:
Make sure the paper is loaded against the front edge
guide and not sticking out from the end of the cassette.
Read these instructions before using your product.
The illustrations show the XP-830, but the steps are the same for
the XP-530 and XP-630.
Note for Spanish speakers/Nota para hispanohablantes:
Para
obtener instrucciones de configuración en español, consulte
la
Guía
de instalación en
epson.com/support/xp530sp,
epson.com/support/xp630sp o epson.com/support/xp830sp
(requiere
una conexión a Internet).
1
Unpack
(XP-630/XP-830)
Note:
• Do not open ink cartridge packages until you are ready to install the
ink. Cartridges are vacuum packed to maintain reliability.
• The CD/DVD tray is taped to the bottom of cassette 2.
1
Remove all protective materials from the product.
2
Lift up the scanner unit and remove all protective
materials.
3
Lower the scanner unit.
2
Turn on and configure
1
Connect the power cord to the back of the printer and to
an electrical outlet.
Caution:
Do not connect to your computer yet.
2
Turn on the product, then adjust the control panel.
3
Select these settings:
XP-530/XP-630: Language
XP-830: Language, country, date, and time
Note:
• You can change these settings later using the product’s control
panel. For more information, see the online User’s Guide.
• If an error message appears, turn off the product and check
that no protective material has been left inside the product.
3
Install ink cartridges
1
Lift up the scanner unit.
Caution:
Do not touch the flat, white cable.
2
Gently shake the Black (BK) ink cartridge. Do
not shake
Photo Black (PBK) or other ink cartridges.
3
Unpack the ink cartridges.
Caution:
Do not touch the areas shown below. Doing so may
prevent normal operation and printing.
4
Remove the cap from each ink cartridge. Store the caps in
the included plastic bag.
Note:
Save the caps and use them to recap the ink cartridges
after removing them for storage or disposal.
5
Insert the cartridges at an angle in the holder for each
color. Press each cartridge down until it clicks.
6
Lower the scanner unit.
7
The printer starts charging the ink. Ink charging takes
approximately 7 minutes. When you see a completion
message on the printer’s LCD screen, charging is
complete.
Caution:
Don’t turn off the printer or raise the scanner unit while
the printer is charging or you’ll waste ink.
Note:
• The printer is designed for use with Epson
®
cartridges only, not
third-party cartridges or ink.
• The cartridges included with the printer are designed for
printer set up and not for resale. After some ink is used for
charging, the rest is available for printing.
XP-530/XP-630/XP-830 Small-in-One
®
Printer
