Start Here
4
Slide the edge guides against the paper, but not too
tight. Make sure the paper is under the tabs on the edge
guides.
5
Gently insert the paper cassette at the bottom of the
printer.
Note:
The paper may slide forward slightly as you insert the
cassette. This is normal.
6
Extend the output tray and raise the paper stopper as
shown. (Do not raise the paper stopper for legal-size
paper.)
6
Connect the fax line
To fax, connect the included phone cord to a telephone wall
jack and to the LINE port on the back of your product. To
connect a telephone or answering machine, use the EXT. port
on your product. See the online
User’s Guide
for more details.
Note:
If you’re connecting to a DSL phone line, you must use a DSL
filter or you won’t be able to fax. Contact your DSL provider for the
necessary filter.
Read these instructions before using your product.
1
Unpack
French
control panel
sticker
Caution:
Do not open ink cartridge packages until you are ready to
install the ink. Cartridges are vacuum packed to maintain reliability.
Remove all tape and protective materials, including the foam and
plastic inside the printer.
2
Turn on
1
Connect the power cord to the back of the printer and to an
electrical outlet.
Caution:
Do not connect to your computer yet.
2
Press the
power button.
3
Select settings
1
To select
English
as your language, press
OK
.
If you want to change the language, select it and
press
OK
.
2
Select your country and press
OK
.
3
Select
Summer
if Daylight Saving Time is in effect
(spring through summer); otherwise, select
Winter
.
Press
OK
.
4
Select the date format and press
OK
.
5
Use the numeric keypad to set the date and press
OK
.
6
Select
12h
(
AM
/
PM
) or
24h
and press
OK
.
7
Use the numeric keypad to set the time and press
OK
.
Note:
You can change the date and time settings by pressing
Setup,
selecting
Printer Setup
, then selecting
Date/Time
.
4
Install ink cartridges
1
Open the front cover.
2
Unpack the four ink cartridges.
3
Shake each cartridge as shown for about 5 seconds.
4
Install each cartridge in the correct slot for its color. Push
each cartridge in until it clicks.
5
Close the front cover.
The printer starts priming the ink. This takes about
12 minutes. When you see a confi rmation message on
the product’s LCD screen, priming is complete.
Note:
The included cartridges prime the printer and print about
1000 black pages/900 color pages. Actual page count will vary.
Caution:
Don’t turn off the printer or open the cover while it is
priming or you’ll waste ink.
6
When you see this menu on your product’s LCD screen,
do not press the
OK
button yet. Continue with the
instructions in the following sections to load paper in
your product and install software.
5
Load paper in the cassette
You can load letter-, A4-, or legal-size plain paper in the
cassette. For instructions on loading envelopes and special
paper in the rear MP tray, see the online
User’s Guide
.
1
Pull out the paper cassette.
2
Slide the edge guides outward, and position them for the
type of paper you are using.
Note:
If loading legal-size paper, extend the cassette as shown.
3
Insert the paper with the printable side facedown.
Note:
Make sure the paper is loaded against the edge guide
and not sticking out from the end of the cassette.
*412238200*
*412238200*
WorkForce
®
Pro WP-4533 Series
4122382 Rev.0
1-F
C
4122382 Rev.0
1-F
M
4122382 Rev.0
1-F
Y
4122382 Rev.0
1-F
K
