8
Close the ink tank cover, then close the scanner unit.
9
Raise the control panel, then press the power button to
turn on the product. The power light flashes.
Note:
If an error code appears, turn off the product and check
that no protective material has been left inside the product.
10
Select your language.
Note:
You can change this setting later using the product’s
control panel. For more information, see the online User’s Guide.
11
When an Epson Smart Panel message appears on the
LCD screen, select the option to continue setup without
the app.
12
When the message to see the Start Here sheet appears
on the LCD screen, press and hold the help button for
5 seconds.
13
Follow the on-screen instructions to start ink charging. Ink
charging takes about 10 minutes.
Note:
When the
power light stops flashing, ink charging is
complete. Once initial setup of the printer is complete, you can
top off the ink tanks with any remaining ink. See the online User’s
Guide for instructions.
Caution:
Do not unplug or turn off the product, or raise the
scanner unit while the product is charging or you’ll waste ink.
Note:
After some ink is used for charging, the rest is available for
printing.
14
Press the OK button to proceed with initial setup.
15
Follow the on-screen instructions to adjust the print
quality of your product.
Note
:
•
You need to load paper before you can adjust the print quality.
See “Load paper” on this sheet for details.
•
Select Adjust Later if you want to adjust the print quality later.
For more information, see the online User’s Guide.
Caution:
After setup, periodically inspect the ink levels to ensure they
do not fall below the lowest lines on the tanks. Prolonged use when
ink is below the lowest line could damage the product. See the online
User’s Guide for refilling instructions.
IMPORTANT: Before using this product, make sure you read
these instructions and the safety instructions in the online User’s
Guide.
Note:
As part of the ReadyPrint™ program, Epson monitors ink usage
remotely to provide you with additional ink before you run out of it. The
product must be connected to the Internet to function and monitor ink
usage.
1
Unpack
Note:
Do not open the ink bottles until you are ready to fill the ink
tanks. The ink bottles are vacuum packed to maintain reliability.
1
Remove all protective materials from the product.
Caution:
Do not touch the flat white cable or the ink tubes and
their translucent cover.
2
Connect the power cord to the back of the product and to
an electrical outlet.
Caution:
Do not connect to your computer yet.
2
Choose a setup method
The Epson Smart Panel
®
app can help you set up your printer
through an interactive, step-by-step process using your
smartphone or tablet.
If you do not want to
use a mobile device for
setup, skip to the “Fill ink
tanks” section below.
To use your mobile device
for setup, continue to
step 1.
or
1
Download the Epson Smart Panel app
from your device’s app store. Do not
launch the app yet.
2
Press the power button to turn on the product.
Note:
Do not connect your product to your computer yet.
3
Launch the app and follow its instructions to set up your
product.
For information on connecting your product to a computer, using
voice-activated printing, or solving problems, or for details on
reaching Epson support, see the sections on the back of this
sheet.
3
Fill ink tanks
Warning:
Keep the ink bottles out of the reach of children and do not
drink the ink.
Caution:
This product requires careful handling of ink. If ink spills, wipe
it off immediately with a damp towel to avoid permanent stains. If ink gets
on your clothes or belongings, it may not come off.
Note:
•
Use only Epson
®
570 ink provided to you under the ReadyPrint
program.
•
Use the ink bottles included with the printer to set up the product. Part
of the ink will be used to charge the print head. These bottles may print
fewer pages compared with replacement ink bottles.
1
With the scanner unit raised, open the ink tank cover, then
open the cap for the black (BK) ink tank.
Note:
Refer to the color-coded sticker to identify the color of each
tank.
2
Unpack the black (BK) ink bottle. Hold the ink bottle upright
and slowly turn the bottle cap to remove it.
Caution:
Do not shake or squeeze the ink bottle. Do not touch the
top of the ink bottle after its cap is removed.
3
Insert the ink bottle into the filling port.
Note:
Do not force the bottle into position; each bottle is keyed for
each color.
4
Wait for the ink to fill the tank.
Do not squeeze the bottle or
allow it to contact any other
surface.
Note:
Ink flows into the tank and
stops automatically when the ink
tank is filled to the upper line. If
ink does not flow from the bottle,
lift and reinsert the bottle.
5
When the ink tank is full, remove the ink bottle and securely
close it with the bottle cap. If any ink remains in the bottle,
close the bottle and store it for later use.
Note:
Do not leave the ink bottle inserted; otherwise the bottle may
be damaged or ink may leak.
6
Securely close the black ink tank cap.
7
Repeat the previous steps for the other colors.
ET-3850U
Start Here
