manualshive.com logo in svg

Epilog Laser Fusion, Manual

The Solid State Logic Fusion is a powerful audio processing unit that combines vintage analog warmth with cutting-edge digital technology. Unlock the full potential of your music production with this versatile device. Enhance your understanding and maximize its features with the comprehensive user manual, available for free download at manualshive.com.

Share
Download
background image

 

Adjusting the Table Level 
Fusion and FiberMark Fusion 
Revision Date: 9/10/2014 

 

pg. 1 of 10 

EPILOG LASER 

16371 Table Mountain Parkway 
Golden, Colorado 80403 
Phone 303-215-9171 
FAX 303-277-9669 
www.epiloglaser.com 

 

Adjusting the Table Level 

For the Epilog Fusion and FiberMark Fusion 

9/ 10/ 20 14  

Requirements: 

Tools: 

•

  3/32” Allen Wrench 

 

•

  Manual Focus Gauge 

 

When to use this document: 

•

  Uneven power in various areas of the table. 

•

  Reduction in quality in various areas of the table. 

•

  General reduction in power or quality. 

•

  Inconsistent or Inaccurate Auto Focus. 

•

  When instructed by Epilog Tech Support. 

Overview: 

This procedure will guide you through the process of properly checking and 

adjusting the table level on the Epilog Fusion. This will ensure proper focus on every 
point of the engraving area. 

 

Summary of Contents for Fusion











Reviews:

No comments

Related manuals for Fusion

CO/Tech S1J-AJ8-10 Instruction Manual preview
S1J-AJ8-10
Brand: CO/Tech Pages: 24

Brands by name

Popular brands

Load more brands