ENFORCER Ethernet over Coax with PoE
4
SECO-LARM U.S.A., Inc.
PoE device doesn’t
function properly
•
If distance is over 328ft (100m), ensure that the link speed is set to 10Mbps
•
Check that the PoE mode switch is set correctly and is the same on both
transmitter and receiver
•
Make sure the input device is turned on
•
Make sure the output device is turned on
•
Test the coax cable between the receiver and transmitter to make sure it is
operational
•
Try installation again using the crossover cables and setting the PoE mode
switch to “End Span” in the process described in “Sample Installation” on pg. 3.
Troubleshooting:
PoE Surge Protectors
PoE Injectors
PoE Repeaters
IPV-P188Q
NJ-P101M-PQ
NR-P101FQ/TQ
Ethernet over Coax
Ethernet Extenders
Basic Ethernet Extenders
IPB-A1200Q
IPB-A1100Q
NE-SE01-020Q
IMPORTANT:
Users and installers of this product are responsible for ensuring this product complies with all national,
state, and local laws and statutes related to monitoring and recording audio and video signals. SECO-LARM
will not be
held responsible for the use of this product in violation of any current laws or statutes.
®
PITSW4
MiNE-AE01-030TQ_150612.docx
Also Available from
SECO
SECO
SECO
SECO----LARM
LARM
LARM
LARM
®
:
NOTICE:
The information and specifications printed in this manual are current at the time of publication. However, the
SECO-LARM policy is one of continual development and improvement. For this reason, SECO-LARM reserves the right to
change specifications without notice. SECO-LARM is also not responsible for misprints or typographical errors.
Copyright © 2015 SECO-LARM U.S.A., Inc. All rights reserved. This material may not be reproduced or copied, in whole or
in part, without the written permission of SECO-LARM.
WARRANTY:
This SECO-LARM product is warranted against defects in material and workmanship while used in normal
service for one (1) year from the date of sale to the original customer. SECO-LARM’s obligation is limited to the repair or
replacement of any defective part if the unit is returned, transportation prepaid, to SECO-LARM. This Warranty is void if
damage is caused by or attributed to acts of God, physical or electrical misuse or abuse, neglect, repair or alteration,
improper or abnormal usage, or faulty installation, or if for any other reason SECO-LARM determines that such equipment
is not operating properly as a result of causes other than defects in material and workmanship. The sole obligation of
SECO-LARM and the purchaser’s exclusive remedy, shall be limited to the replacement or repair only, at SECO-LARM’s
option. In no event shall SECO-LARM be liable for any special, collateral, incidental, or consequential personal or property
damage of any kind to the purchaser or anyone else.
SECO-LARM
®
U.S.A., Inc.
16842 Millikan Avenue, Irvine, CA 92606
Website: www.seco-larm.com
Phone: (949) 261-2999 | (800) 662-0800 Email: [email protected]
NE-AE01-030TQ
Ethernet over Coax with PoE
Manual
•
Extends powered Ethernet devices, such as cameras with PoE, over existing coax cable
•
Connects cameras with PoE to 10/100BaseT PoE Injector/Switches over single coax cable
•
Supports PoE: IEEE802.3af/at
•
Supports 10/100 Mbps transmission rate
•
Can extend up to 984ft (300m)
Note:
Works only with PoE compatible devices
