background image

Installer: 

Leave this manual with the appliance.

Consumer:  Retain this manual for future reference.

WARNING: If the information in these instructions 

are not followed exactly, a fire or explosion may 

result causing property damage, personal injury 

or loss of life.

—  Do not store or use gasoline or other flammable 

vapors and liquids in the vicinity of this or any 

other appliance.

—  WHAT TO DO IF YOU SMELL GAS

 

•  Do not try to light any appliance.

 

•  Do not touch any electrical switch; do not use 

any phone in your building.

 

•  Immediately  call  your  gas  supplier  from  a 

neighbor’s phone. Follow the gas supplier’s 

instructions.

 

•  If you cannot reach your gas supplier, call the 

fire department.

—  Installation and service must be performed by a 

qualified installer, service agency or the gas sup

-

plier.

Page 1

INSTALLATION INSTRUCTIONS

AND

OWNER’S MANUAL

FAN TYPE

 VENTED 

WALL FURNACE

MODEL

FAW55IPXLP-1

FAW55IPXNAT-1

WARNING: If not installed, operated and maintained 

in accordance with the manufacturer’s instructions, 

this product could expose you to substances in fuel 

or  from  fuel  combustion  which  can  cause  death  or 

serious illness.

Summary of Contents for FAW55IPXLP-1









































Reviews: