EZM-4430,EZM-4930,EZM-7730,EZM-9930
Programmable Counters
- 6 digits Process (PV) and 6 digits Set (SV) Value Display
- Operation with 1 Set Value
- Reset , Pause and ChA-ChB Counting Inputs
- NPN/PNP Type Operation
- Operation with Automatic and Manual Reset
- INC,DEC,INC/INC,INC/DEC,UP/DOWN, x1 / x2 / x4 Counting
with Phase Shifting Property
- Multiplication Coefficient and Decimal Point Position
EZM-4430,EZM-4930,EZM-7730,EZM-9930
Programmable Counters
Electrical Wirings
Introduction Brochure. ENG
EZM-XX30 01 V04 03/17
SPECIFICATIONS :
INPUTS :
Output :
Process
Relay Output (5A@250V
at Resistive Load)
V
Counting Inputs (Ch-A,Ch-B):
Reset Input:
Pause Input:
Sensor Type Selection:
Reset Function:
Count Input Types and Maximum Frequency :
Reset and Pause Input Filter : 2-50 msec
OUTPUT
Switch, Proximity, Capacitive
sensor or encoder can be connected.
Switch, Proximity, Capacitive sensor or encoder can
be connected.
Switch, Proximity, Capacitive sensor or encoder can
be connected.
NPN or PNP can be selected.
Automatic or Manual.
INC,DEC,INC/INC,INC/DEC,UP/DOWN max.20 kHZ.
x1 / x2 / x4: Phase Shift( for encoder ) Counting;Max.10 kHZ.
(Can be adjusted in
parameter.)
DISPLAY :
Process Value Display :
Set Value Display :
LED Display :
EZM-4430 : 8 mm Red 6 digit LED Display
EZM-4930 : 13.2 mm Red 6 digit LED Display
EZM-7730 : 10.8 mm Red 6 digit LED Display
EZM-9930 : 13.2 mm Red 6 digit LED Display
EZM-4430 : 8 mm Green 6 digit LED Display
EZM-4930 : 8 mm Green 6 digit LED Display
EZM-7730 : 8 mm Green 6 digit LED Display
EZM-9930 : 8 mm Green 6 digit LED Display
SV(Set value),OP(Output Position) LEDs.
ENVIRONMENTAL RATINGS and PHYSICAL SPECIFICATIONS
Operating Temperature
Humidity
Protection Class
Weight
Dimensions
Panel Cut-Out:
none condensing),
at front,
at rear.
Depth
Depth
Depth
Depth
:
:
:
:
:
0...50°C
0-90%RH (
Ip65
Ip20
EZM-4430 : 10 gr.
EZM-4930 : 40 gr.
EZM-7730 :
0 gr.
EZM-9930 :
0 gr.
EZM-4430 : (48 x 48mm,
:95 mm)
EZM-4930 : (96 x 48mm,
:96 mm)
EZM-7730 : (72 x72mm,
:95.5 mm)
EZM-9930 : (96 x 96mm,
:96 mm)
EZM-4430 : (48 x 48mm)
EZM-4930 : (96 x 48mm)
EZM-7730 : (72 x72mm)
EZM-9930 : (96 x 96mm)
2
2
27
34
SUPPLY VOLTAGE
230 V
50/60 Hz (-15%;+10%) 2.3VA
115V
(-15% ; +10%) -2.3VA
24V
50/60 Hz (-15% ; +10%) 2.3VA
(Must be determined in order.)
V
V
V
24 V
(-%15;+%15) / 24 V
50/60Hz(-%15;+%15)
Z
V
4VA
DIMENSIONS
PANEL MOUNTING
1-
2-
3-
Before mounting the device
in your panel, make sure that
the panel cut-out is suitable.
Check front panel gasket
Position.
Insert the device through
the cut-out. If the mounting
clamp are on the unit, put out
them before inserting the unit
to the panel.
4-
Insert the unit in the panel
cut-out from the front side.
5- Insert the mounting clamps
to the holes that located top
and bottom sides of device
and screw up the fixing screws
until the unit completely
immobile within the panel.
Panel Cut-out
Sensor
Supply
Relay Output
Supply Switch
Fuse
Sensor
Supply
Relay Output
Supply Switch Fuse
Sensor
Supply
Relay Output
Supply Switch Fuse
Sensor
Supply
Relay Output
Supply Switch Fuse
4
5
96mm / 3.78 inch
48mm/1.89inch
72mm/2.83inch
72mm / 2.83 inch
11.5
mm / 0.45 inch
±1
84mm / 3.31 inch
11.5
mm / 0.45 inch
±1
84mm / 3.31 inch
Maximum 15 mm / 0.59 inch
Maximum 15 mm / 0.59 inch
Maximum 15 mm / 0.59 inch
10.5
mm / 0.41 inch
±1
76mm / 2.99 inch
96mm / 3.78 inch
SV
SV
OP
OP
Counter
EZM-4930
SET
P
RESET
Maximum 15 mm / 0.59 inch
11.5
mm / 0.45 inch
±1
84mm / 3.31 inch
48 mm / 1.89 inch
48mm/1.89inch
96mm/3.78inch
EZM-4430
EZM-4930
EZM-7730
EZM-9930
65 mm / 2.56 inch (min)
46mm / 1.81 inch(min)
46mm/1.81inch(min)
65mm/2.56inch(min)
129 mm / 5.08 inch (min)
46mm/1.81inch(min)
65mm/2.56inch(min)
97 mm / 3.82 inch (min)
69mm / 2.72 inch(min)
69mm/2.72inch(min)
97mm/3.82inch(min)
129 mm / 5.08 inch (min)
92mm/3.62inch(min)
129mm/5.08inch(min)
92mm / 3.62 inch(min)
92mm / 3.62 inch(min)
