EMC2 VNXe 3300 System Hardware Installation Manual Download

Page: 1 / 20

This document explains the installation procedures for an EMC

VNXe3300

system in a Telco rail self-supporting rack, and describes the kits available
for mounting the devices in a VNXe3300 system. These kits are for Telco rail
self-supporting racks

only.

Introduction ............................................................................................. 4

◆

VNXe3300 system devices .................................................................. 4

◆

Telco rail self-supporting rack .............................................................. 4

Device placement guidelines .................................................................... 5

◆

Position in rack ................................................................................... 5

◆

Device dimensions .............................................................................. 5

◆

Power considerations .......................................................................... 5

Installing a VNXe3300 DPE in a Telco rack................................................. 7

◆

VNXe3300 DPE mounting kit (DPE-TELCO-3U/3US)............................... 7

◆

Installing VNXe3300 DPE mounting trays............................................. 8

◆

Installing the VNXe3300 DPE in the mounting trays ............................. 9

Installing a 3U DAE in a Telco rack........................................................... 12

◆

3U DAE mounting kit (FRAME-T-PDAE/PDAES) .................................... 12

◆

Installing 3U DAE mounting trays....................................................... 13

◆

Installing the 3U DAE in the mounting trays ....................................... 15

Installing a 2U DAE in a Telco rack........................................................... 17

◆

2U DAE mounting kit (FRAME-T25DAE/T25DAES) ............................... 17

◆

Installing 2U DAE mounting trays....................................................... 18

◆

Installing the 2U DAE......................................................................... 20

EMC

VNXe™3300 System

Hardware Installation Guide
for Telco Racks

P/N

300-012-893

REV 02

Summary of Contents for VNXe 3300 System





















Search results

Summary of Contents for VNXe 3300 System

Reviews:

Related manuals for VNXe 3300 System

Brands by name

Popular brands

EMC2 VNXe 3300 System, Hardware Installation Manual

Search results

Summary of Contents for VNXe 3300 System

Reviews:

Related manuals for VNXe 3300 System

Brands by name

Popular brands